3962VVV Magic Chef Microwave Oven Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kimbel from Rhoadesville, VA
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Varying heat
Removed two screws, unplugged the old unit, plugged in the new, screwed the new in. Job done. Would have been less than five minutes if I hadn't kept dropping the screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Schwenksville, PA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
oven light burnt out
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- peggy ann from forest city, NC
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced oven lightbulb
very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Plaistow, NH
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Oven temperature all over the place
I slide the oven out from the counter and unpluged it. I removed all the oven racks. I then removed the machine screws that held the sheet metal that covered the back of the unit. This made it a lot easier to disconnect the long oven sensor wire and put the wire through the insulation. I removed the two screws on the inside of the oven that held the sensor onto the inside rear wall of the oven. The old sensor did not test too bad but the temperature is reaching the set temperature. I still had to adjust the oven temp up ten degrees using the control panel. I have learned that it takes a few cycles of the element going off and on during the warming to reach the desired set temperature. One more issue is that the buzzer goes off signaling that the set temperature has been reached when it has not. When I set it for 350 F the buzzerr goes off at 280 F and I have a good oven thermometer. I own three oven thermometers and they all read the same. We use to have nothing but Maytag appliances but no more. We have had issues with Maytag front loading washers and ranges. PartSelect is great. Good prices and fast delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Ada, MI
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bulb went out in my oven
My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Phoenix, AZ
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bulb Replacement
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- george from San Antonio, TX
- Parts Used:
- 12001656
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
Oven would not work
Installed new thermostat. Went well. Now the oven comes on and it takes 2.5 hours to come up to 250 degrees. Help!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Summerfield, FL
- Parts Used:
- 7403P239-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replace 8" Element Switch
Disassembled upper unit with Phillips screwdriver. Removed 2 "plug connectors" from element switch. Replaced switch. Plugged both connectors back onto switch. Reassembled the upper portion of the range. Tested and OK
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Virginia from Oceanside, CA
- Parts Used:
- W11665456
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench (Adjustable)
leg was bent, also metal receiving bracket bent
Removed stove from slot in wall. Bent rear left leg would not unscrew due to bent metal bracket. Used hacksaw to cut out leg, then straightened metal bracket with small hammer and was able to screw new leg in and adjust height by using level on stove before reinserting stove its slot. Recheck level after pushing back in place and adjust front legs if necessary. If not for bent metal receiving bracket, would have taken much less time. Still easy tho. R'cvd part in two days. Very quick.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KENNETH from DEEP RUN, NC
- Parts Used:
- 7403P239-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
burned out switch
killed power...removed back of stove...removed switch and replaced it..reinstalled back...powered up
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Milton, FL
- Parts Used:
- 7403P239-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Front burner would not heat properly.
Ordered a front burner but it was not the right size. Ordered a switch after local dealer said I had a bad switch. Ordered a switch from Parts Select and received it the next day. Works good now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jayne from Willimantic, CT
- Parts Used:
- W11665456
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Leveling legs were broken during the summer
The range in my classroom had the leveling legs broke off by the summer staff. I ordered two new leveling legs and the night custodian replaced them in about 45 minutes and them leveled the stove. Parts were just as stated and easy to order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Crestwood, MO
- Parts Used:
- W11665456
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken leveling leg.
This is a no brainer. I am only doing this because you asked. Pull out the stove, tilt it back, remove broken leg, install new leg.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clarence from Monroe, WI
- Parts Used:
- W11665456
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Used stove was missing 1 leg.
My used stove had been dropped by the previous owner. While I could live with the minor scratches on one side the wooden shims holding up one corner were annoying. A new leveling leg was less than $2. I used a pair of needle nose pliers to straighten the mounting hole and screwed the new leg in. This used stove was originally $2000 but I bought it for $999. the new leg plus shipping was about $10. What a deal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sreve from Deland, FL
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven would not program and would shut down
The "PartsSelect" General discription of the parts funtion helped me to confirm my suspitions that there was some form of temperature registering problem. I whatched the short video they provided on how to change the part out, even though, in this case, it's pretty self explanitory.The part was in my hands a day erlier than promised and in reality, much earlier than I had anticipated from the beginng. It took me all total, 20 minutes to exchange the part out and have the oven in operation again.
Was this instruction helpful to you?
Thank you for voting!