28FN-6CXWV8-DZ Magic Chef Microwave Oven Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joe from RAIL RD FLAT, CA
- Parts Used:
- 8206232A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Light bulb out
Put s pot under were you take the screw out.If you drop it you can get it easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jared from UNION GROVE, AL
- Parts Used:
- WPW10245259
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
The oven and ranges would not heat up and an F9 error was displaying on the Oven Screen.
So, the F9 error indicates a electrical power issue. First I pulled the oven out and verified I had 240 volts at my outlet.
Then I removed the fire panel over the terminal block and the issue was apparent. The nuts on the terminal block were corroded. This had cause the resistance in the connection to raise and burn up the wire to my oven plug at the terminal block.
I removed the whole back panel and everything else seemed OK visually.
1. I go new connectors for the oven plug, stripped the wires, and crimped on the new connectors.
2. The terminal block DOES NOT come with the nuts to connect the wire to the terminal block. Mine were so corroded they had to be replaced. So I went and purchased the correct ones and installed the terminal block and reconnected all the wires.
3. I applied some dielectric grease to the connections through out the process of reinstalling to prevent it from happening in the future.
Then I removed the fire panel over the terminal block and the issue was apparent. The nuts on the terminal block were corroded. This had cause the resistance in the connection to raise and burn up the wire to my oven plug at the terminal block.
I removed the whole back panel and everything else seemed OK visually.
1. I go new connectors for the oven plug, stripped the wires, and crimped on the new connectors.
2. The terminal block DOES NOT come with the nuts to connect the wire to the terminal block. Mine were so corroded they had to be replaced. So I went and purchased the correct ones and installed the terminal block and reconnected all the wires.
3. I applied some dielectric grease to the connections through out the process of reinstalling to prevent it from happening in the future.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from RIVERSIDE, CA
- Parts Used:
- 8009
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
light bulb in water ice freezer door went bad
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marcus from Emmett, KS
- Parts Used:
- 12001676
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner no longer worked.
First I removed a screw that held the element in place then disconnected the two wires . Then I just reattached the two wires put the screw back in place and was done in about 10 minutes. Fairly easy fix, I had this go out a few years ago and had a repairman fix it, and saw how easy it was, so this time I did it myself. Easy job!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from Mountain City, TN
- Parts Used:
- WPW10196405, WPW10196406
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The drip bowls were all caked and corroded.
This wasn't a "repair", but I got an email asking for my story, so here it is. :-)
I followed the owner's manual instructions by pulling out the burner elements, lifting up the old drip bowls, setting in the new ones, replacing the elements.
I followed the owner's manual instructions by pulling out the burner elements, lifting up the old drip bowls, setting in the new ones, replacing the elements.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Bellefonte, PA
- Parts Used:
- W11122006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner would not work
slide stove out unplugged it took six screws out put new one in transfered wires pluged back in and it works thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- patricio from chicago, IL
- Parts Used:
- WPY01050009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
no power at all
unscrew microwave's cover,test the fuse which is located at top rear left side, the fuse is inside a plastic tube,if the fuse is burnout,just replace it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Shirley, IN
- Parts Used:
- WP3191454
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken terminal
Simply removed the old heating element and plug the new element terminals into socket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Prescott, MI
- Parts Used:
- 7201P036-60
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Burned up oven door gasket needed replaced.
I started by removing the door, then trying to remove all of the screws in the oven casing. Of course the very middle screw in the bottom of the oven was rusted and dammged by use. I had to use a drill bit and remove the old screw. After dissasembly of the oven casing, I found that the lip that supports the gasket was rusted and burnt away about 3/4 in. I placed the new gasket in and found that when closed it covered this defect and sealed. I reassembled and cheked for operation.Ok! Imortant--remove the elements before removing oven casing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paula Collins from Needham, MA
- Parts Used:
- WP3191454
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old coil broke.
After I removed the piece of metal separating the two wires, I inserted the unit with no problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kat from Hudson, NC
- Parts Used:
- 8206232A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lights bulbs burned out
Really easy for a 75-year old female; just spent more time reading the online manual than actually installing the light bulbs to find out where to access the light bulbs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAN from CARPENTERSVLE, IL
- Parts Used:
- 8206232A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
light bulb burnt out .
Turn off power supply at breaker . Replace old bulb with new bulb .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from MERIDIAN, ID
- Parts Used:
- 8206232A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Range light bulbs were burned out
We needed a phillips head screw driver to remove the single screw holding the light bulb cover in place.
Removing the old bulbs was a little work, because they had come loose from the sockets. We unplugged the microwave, so we could grip the sockets with a tool. I think my husband used a needle nose plier for this.
The new bulbs screwed in easily, and then we refastened the light bulb cover with the phillips head screw driver.
Removing the old bulbs was a little work, because they had come loose from the sockets. We unplugged the microwave, so we could grip the sockets with a tool. I think my husband used a needle nose plier for this.
The new bulbs screwed in easily, and then we refastened the light bulb cover with the phillips head screw driver.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pablo from Burlingame, CA
- Parts Used:
- 8206232A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bulb burned-out
screwed in new bulb
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eugene from San Antonio, TX
- Parts Used:
- 12001676
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Burner wouldn't heat (wiring failure)
1. Shut the breaker off; Jenn-Air's design will have you working around hot leads if you don't.
2. Raise the control panel
3. Remove burner and unscrew the burner connector; trace the wires back to the control panel bottom and remove them
4. On the replacement connector, add the electrical for the control panel. These are not included and can be found at any hardware store; they are a standard size.
5. Connect the new wires and put everything back together.
6. Reset the break and test.
2. Raise the control panel
3. Remove burner and unscrew the burner connector; trace the wires back to the control panel bottom and remove them
4. On the replacement connector, add the electrical for the control panel. These are not included and can be found at any hardware store; they are a standard size.
5. Connect the new wires and put everything back together.
6. Reset the break and test.
Was this instruction helpful to you?
Thank you for voting!