77JN-5EVWM Magic Chef Microwave Oven Combo - Instructions

Turned breaker off to oven, removed two screws disconnected two wires. Reversed order to install. Piece of cake. Stuart,in va.

It was very simple. First thing I did was to go online to youtube and type in the kind of repair I intended to do. There were several short videos showing you how to do the replacement.It was easy and took about 30 to 45 minutes. First thing is shut off the power to the oven. ( Very important). You then need to take out two screws that hold the element in place. At this point, just pull the element toward the front of the oven. You will see some insulation at the hole where the wires come out. Slowly work the element forward until you see the fasteners on the wires ( two wires).Disconnect the fasteners and throw the old element out and put the new one in the oven.Connect the element, push everything back into the hole and screw the element to the back wall. You're done ! I had two wall ovens to fix.

Great I can bake now

The instructions reviewed in the Maytag Parts web site provided very good information that told me how to remove and replace the heating element. It took me about 15 minutes to complete the replacement. The oven then began to function properly.

I am impressed with the rate I was sent the replacement. I received the replacement within 24 hours after I submitted the request for the product.

Turned off oven power.Removed oven heat shield, element support clips and element mounting plate screws. Disconnected three element power wires and ground wire. Removed old element. Reversed removal procedure for new element install. Piece of cake.

I just removed the lamp retainer plate and glass cover, inserted the new gasket, and screwed everything back in place. Simple as that. I was enormously pleased that the part arrived so quickly -- just in time for me to cook my Thanksgiving turkey and use the self-cleaning feature.

Turned off the breaker first. Remove the mounting screws and unplug the element. Then replace the new element. Then put in the mounting screws and turn the breaker on. Easy.

I TURNED THE POWER OFF !!! removed the two screws holding the element in place, disconnected the two power wires, installed the new element. Done, in less than five minutes.

Unscrewed old element from back of oven, disconnected and reinserted new element and screwed back into place. Voila! So glad to have saved the cost of a repairman. Where I live this would have been a $200 repair(part and service call) easily. This repair took no time at all. Very please as to how fast Parts service got the part to me. I use my oven a lot, so I was lost without it.

I took the broiler pan out of the shipping container and put it in the oven.

I made the mistake of thinking that, if the oven was off, there would be no voltage to the heating element. Wrong! I removed the element, wearing rubber gloves just for safety, and had no problem. But when I put the wiring back on the new element and tried to slide it into the hole at the back of the oven, one of the wires brushed the metal, sparks flew, and melted one of the wires. Even though the oven was off, this wire was hot. The solution was, of course, just to turn off the circuit breaker, reconnect the wire, and slide the element back in. It works fine now.

This was too simple, turned off the power to the oven, undid the two screws, unplugged two wires, plugged wires into the new element, fastened the new screws and turned the power back on. Turned on the oven, what do you know, it works again!

The element did not come with instructions and none were needed.

Very easy. Didn't have to replace whole unit

remove two bracket screws, and remove bracket, the remove two mount screws for element. then remove the element. installed the element in reverse order that it was removed.

All went well except for error on instruction sheet.
Ground wire used on earlier Models attached to the ground lug is no longer used?? and should be removed!!! Guess what the ground wire has to be used or the element will not heat up.Soooo someone at the mfg. has no ideal what they are talking about,You have to ground the element or it will not come on.