3968XVB Magic Chef Microwave Oven Combo - Instructions

Removed the two screws holding the element in place. I then pulled the element and wiring out until I saw the connecter. I disconnected the two wires and then chose the correct connector from the package, snapped it back into place, put the screws back, turned on the breaker then tested the oven and found that everything was working correctly.
This is the second time I have ordered from Part Select, the first time was for a front LED panel on the same appliance. With the help finding the part you need and the comments from other customers I have saved a lot of money by repairing these problems myself. Oh, and the best part is the look on my husband's face when he came home and found out the repairs were made by me and not a repairman that he said I should call. He said he would laugh when the first repair by me didn't work but who's laughing now : )

As the video described I just unscrewed the sensor from inside the oven. Although I couldn't pull the wiring harness through the insulation (the wires were gathered in back with a wire tie) just four screws to loosen the back panel for access to the connection. My wife says it seems to be heating perfectly now.

Turn off breaker.
Remove knob, pulls off. Pulled stove away from wall.
Removed front panel with switches attached.
There are screws in front and back.
Removed screws that hold switch in place.
Transferred wires one at at time to get proper location.
Reverse process for reassembly
Gary in Ohio

I was told by appliance repairman that sensor and electronic panel were out - so ordered both as PartSelect was less expensive (about 1/2) than service call price. Sensor was in stock and arrived in 2 days, panel was special order from factory.
Replaced the sensor. Pressed Control Lock pad for several seconds and oven clock came on. Was able to set baking temp, broiler, and convection operation as normal.
Canceled order on panel as Sensor fixed my problem.

First thing- I cut off power to the range. I then removed two screws to allow the cook top to be lifted. I marked the wiring and replaced the burner. Reapplied power and started cooking!

SHUT OFF BREAKER FOR OVEN! pulled oven out to get at backside,removed 3 screws on back coverplate,removed 2 screws inside oven at sensor in top left corner of oven,disconnected plastic clip at back ,pulled old sensor through hole.replaced sensor with new in reverse order. 15minutes tops.

I ohmed out the burner element that wasnt working and found it was open. I ordered a new element thru PartSelect and installed it in the stove. I powered up the stove and turned on the burner but it didnt get hot. After a bit of testing I found that the new elements safety overtemp terminals werent in the same configuration as the original unit. I made some wiring adjustments and the burner was operating properly. Thanks PartSelect

Shut off power to stove. Moved stove out. Loosened screws in top and middle back of stove and removed cover. Took mental note of color order of each wire and unhooked each wire from old switch and reattached to new switch in exact order of color of wire as original. Remounted cover on back of stove and reattached screws. Turned on power and turned on burner and tested burner for heat. Turned off burner, slid stove back and bingo - done. Saved a lot of money.

So, the F9 error indicates a electrical power issue. First I pulled the oven out and verified I had 240 volts at my outlet.

Then I removed the fire panel over the terminal block and the issue was apparent. The nuts on the terminal block were corroded. This had cause the resistance in the connection to raise and burn up the wire to my oven plug at the terminal block.

I removed the whole back panel and everything else seemed OK visually.

1. I go new connectors for the oven plug, stripped the wires, and crimped on the new connectors.

2. The terminal block DOES NOT come with the nuts to connect the wire to the terminal block. Mine were so corroded they had to be replaced. So I went and purchased the correct ones and installed the terminal block and reconnected all the wires.

3. I applied some dielectric grease to the connections through out the process of reinstalling to prevent it from happening in the future.

Had a technician from Home Advisor to check the problem out with my Whirlpool Double oven(1 1/2 old). Paid $60 to find the problem. According to the technician problem was control board and cost of labor and parts $465.00
Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answered my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine.
Thank you, Thank you Part Select for your help and honesty.

Sincerely
Peter from Maryland

I slide the range out and unplugged it from the outlet. I removed the back of the oven ( 8 screws ) using a cordless drill and phillips bit then with a phillips screwdriver I removed the oven sensor (2 screws) then I installed the new sensor , reinstalled the oven back , plugged the range in , slide it back into place and that was it. This repair took about 10 mins and the oven works perfectly. Thanks !

I marked all wires separately attaching a paper strip with tape to each connector and made a separate small chart where each wire should attach to the bottom of the switch. On this particular model there are three or four colored wires and two have both double and single connections to the same switch so the small chart told me where a single or double connector would attach even if I lost the attached taped information. Then since wires were marked separately, even if paper was lost I could still proceed with no outside help.
I had the luxury of leaving the breaker shut off while waiting for part to arrive. After arrival which was only a couple of days, I raised the stove top and let it rest on a small board maybe 1.5 feet so it would keep itself up.
The under assembly was already taken loose before so I just removed the broken switch taking all wires loose, which are already marked and replaced the switch with the new one. Gently placing each wire at its place after removing the tape for that connection. After all four wires were connected I held the switch up in place while screwing the two set screws into place. Then reattached the bottom assembly cover and then let the top down and reattached the four screws, one in each stove hole to attach the stove top to the under assembly. I then reattached one element and flipped the breaker switch on. No sound or problems so I tried the element and all is well. Reattached all elements and the project is done. PartSelect.com made this repair easy and economical. Replacement would have been 4x the part and shipping. Thanks.

FIrst we found the power source ( this took us awhile) and cut the power at the fuse box. then we unplugged the cooktop and started to take out screws. It turned out the screw removal had nothing to do with the stove top coming out. We took the taping knife & pried it under a corner and lifted. the cook top was just sitting on the counter.
The hardest part of the whole job was holding the cook top because we did not disconnect the downdraft fan other than to pull the tape off the vent & fan. Now we could undo the rachet screws that held the glass top to the cook top & remove it.
Theburner was simply a matter of pulling connections loose & placing them on to the new one. The clips that hold the burner in place were removed w/ a screwdriver & replaced on to the new burner. Watch for the numbers on the burner underside to know where to reattache the clips. the unit that lights up to show that a burner is hot would not come off, but we managed to remove
the plastic part even though the clip screw would not loosen, and since it only had to float near by we used the unused wire included in the new part to hold it in place. Putting the unit back together was not too hard, but it took us a little while to get it all lined up. Be carefull of what ever you work on, the downdraft fan scratched up the counter top that we were working on. we started with cardboard under it & should have continued, we did not want to try & remove the fan. Then we put it back in the counter opening & plugged everything back in & to our amazement ( we are not handy people) it worked! the lights that had refused to work when one unit was burned out now worked on all four units. thank you partselect, we were able to do the repair with what you sent.

Left oven off. Located sensor in pdf manual. Unscrewed mount, pulled sensor out to access connector. Disconnected old sensor, checked continuity(resistance) on ohms with multimeter. No continuity; connected new sensor, screwed mount back into place, turned on oven and baked cookies to check operation & it worked perfectly.

Removed the large lower back panel of range (6-8 phillips screws) which holds upper control back panel in place. Removed upper control back panel (2 screws), exposing infinite switch electrical connections. At front face of control panel, removed (pulled off) control knob, exposing 2 phillips screws holding switch in place. (NOTE: A sleeve is on the switch arm or maybe remains inside the control knob). Look for this sleeve. Without it, the knob will NOT seize the switch rotary arm.
Removed each wire connection individually, one at a time, installing it in the proper position on the new switch.
Reverse all procedures to put things back together. A very simple, straight-forward operation.