LMV1680ST ((CSBELGA)) LG Microwave Oven Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- LINDA from OCEAN CITY, MD
- Parts Used:
- 6549W1S013K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
microwave turntable will not turn
removed screws from bottom of microwave... lowered bottom plate.. unplugged motor and replaced with new motor/AC synchronous. Reinstalled bottom plate......... DONE!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Samuel from Daleville, VA
- Parts Used:
- 3501W1A019D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave would not heat food, but everything else worked.
Problem was a faulty door latch switch. I easily accessed the switch by removing the control panel, total of 4 screws. After that, just disconnected the three switch door latch assembly and connected the new one. Took about half an hour and was very easy. Unit works perfectly now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cara from Canfield, OH
- Parts Used:
- ADC49436906
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the handle had become detached for the door because the screw housing had cracked
i removed the broken door by inserting the putty knife between the door jab and the plastic inner face cover. moving around the face cover carefully until all the face cover is detached, remove and set aside. unscrew the 3 screws two hold the handle and on holds the inner door assembly to the front of door once the inner door is free this may need to be detached using a flat head screw drive or putty knife. the outer door removes easily from the hinge pins. repeat the dis-assembly process on the new door being careful not to crack or mark the new door. once the new door is in 3 pieces place the outer door on the hinge pins and carefully snap the middle door into place the screw in the 3 screws making sure the handle is in the correct position. once this is done replace the inner plastic face cover and this snaps into place and that is it you are done door fixed minus the service call and fee. i saved 150. doing it my self
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from Windham, NH
- Parts Used:
- 3B73362F, 6600W1K001C
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Had to lift on the door for the microwave to run, suspected the door switches.
Ordered the switches from Partselect, arrive in two days. Had trouble removing the plastic connectors from the old switch terminals, one of the plastic protectors broke, but was able to reuse it. It took a little figuring out how to remove the existing switches. Must push in a tab and rotate the switch on a little pin, then remove. Must be careful not to break the plastic tabs holding the switches in place. Replaced all (3) switches at the same time. All in all it was pretty easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Wilson, NC
- Parts Used:
- 6549W1S013K
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The turntable in my built-in microwave oven stopped working
First, I checked YouTube to see if there was a video showing how to do the repair ... It's as easy as unplugging the power cord, removing 6-8 screws on the bottom panel, unplugging the wire harness from the AC synchronous motor, removing two screws hold the motor in place, putting the new motor in place with the two screws, connect the two wires to the brass tabs, replacing the bottom panel, reconnecting the power - and you're done. Easy!
Was this instruction helpful to you?
Thank you for voting!