KEHU309SSS00 KitchenAid Microwave Oven Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from MIAMI, FL
- Parts Used:
- W10660052
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Micro Wave Steamer
I spoke to Daily via the phone and I ordered a new steamer since my original steamer cracked over a period of time. No installation, no problems I just recently used it and works perfectly! Thank You!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elena from HOUSTON, TX
- Parts Used:
- W11724411
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- Less than 15 mins
Part broken
We ordered element support 3 times and all three times it came broken. The part is made of porcelain and is fragile , representative asked warehouse to pack it in the box and part still came in envelope.
Requested refund and ordered directly from factory.
Requested refund and ordered directly from factory.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Baytown, TX
- Parts Used:
- W11373838
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I broke the glass cooking tray when instaling my oven microwave combo
I put the tray in the microwave???? Pretty easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Fernandina Beach, FL
- Parts Used:
- W11724411
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken mounting bracket for coils in convection microwave.
Very easy, fit perfectly.No tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from LAKEVILLE, MN
- Parts Used:
- W11724411
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grill support broke. Sounds like a common problem based on other’s comment.
Turn the grill support 90 degrees to the opening in ceiling of micro. Insert then turn back 90 degrees so the support is in-line with the slot. Hang the wire on the support. Hours of worry over what this was gonna cost me to get repaired, then a 45 second fix costing only 29 bucks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from Conyers, GA
- Parts Used:
- W11724411
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The ceramic hanger that holds up the element for the convection over broke
Took about 10 seconds... turn the new ceramic holder sideways, push up in the hole, bring the element up to position and twist the ceramic piece 45 degrees into place to hold element. That's it!!! Very simple....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- frank from Wilmington, NC
- Parts Used:
- WPW10131825
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
All elements would heat to around 200 degrees, then stop
Disconnect the sensor harness and checked resistance on the sensor,should read around 1100 ohm I only got 25.The sensor is mounted in the oven cavity back wall below upper element,the door must be removed. Unscrew 2 Philips head screw,unhook the harness,install new sensor,reconnect harness,install screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LAURIE from BILTMORE LAKE, NC
- Parts Used:
- WPW10131825
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The oven was over heating because it wasn’t reading the temperature
Pulled the stove out, unscrewed the back and plugged the new thermostat in. Screwed the back back on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lewis from WICHITA, KS
- Parts Used:
- WP9760774
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven upper heating element went out.
Turned the breaker off to the stove.
Removed 4 screws holding the element in place.
Disconnected the electric connection from element.
I had to replace the screws which were corroded.
Connect the new element electric connection.
Replace the 4 screws.
Turn on the power.
Turn on oven to burn off the smell of the new element.
You are done.
Removed 4 screws holding the element in place.
Disconnected the electric connection from element.
I had to replace the screws which were corroded.
Connect the new element electric connection.
Replace the 4 screws.
Turn on the power.
Turn on oven to burn off the smell of the new element.
You are done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from ELKTON, OR
- Parts Used:
- WP9760774
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
burnt out element
good, used tie wire with a hooked end to fish one wire out of the back, to keep from removing the oven
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from EUGENE, OR
- Parts Used:
- WP9760774
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replace Broiler Element on a slide in range
Using the video from PartSelect I followed the steps shown. Sliding the range out was difficult so I tilted it forward resting the frame on a 5 gallon plastic bucket. I did have to crimp on a new terminal. The repair was straightforward.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Connie from SAN RAFAEL, CA
- Parts Used:
- WP9760774
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
The broiler unit needed to be replaced
I was stopped by the third screw on the roof of the oven, which was slightly rusted and would not budge in spite of using WD40! I had to enlist the aid of my son who arrived with better tools, including a SQUARE phillips head socket set. He also had to spend some time pinching and slightly reconfiguring one of the attachments in the back which did not slide together naturally. So, for an 82 year old retired housewife this was not as simple as it looked, but it was a piece of cake for guys like Erik with the know-how and the proper tools!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Concord, CA
- Parts Used:
- W11373838
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken glass dish for microwave
no repair needed - ordered part, came within 3 days - very satisfied
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from HOUSTON, TX
- Parts Used:
- WP8203546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
wire came loose and shorted out
Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Palm Coast, FL
- Parts Used:
- WP8203546
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
I snapped a bolt on the main power terminal block when connecting the pigtail.
Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.
Was this instruction helpful to you?
Thank you for voting!