Models > KEMS377GBL4 > Instructions

KEMS377GBL4 KitchenAid Microwave Oven Combo - Instructions

Jump to:

All Instructions for the KEMS377GBL4
121 - 135 of 152
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Raymond from WESTVILLE, IN
Parts Used:
WP4449253
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
I cracked the interior glass door by dropping a dish on it.
Removing the door was the first challenge but once the door was off it was a matter of disassembling the door to get access to the interior door. If you remove all pieces and line them up in the order that they are removed you have a good chance for success.
Was this instruction helpful to you?
Thank you for voting!
Customer:
william from Wellington, FL
Parts Used:
WPW10016550
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Blower very loud noise, all the time.
Removed double oven from cabinet after removing the doors, placing it on a milk crate, needs two people, turned it slightly to access the rear panels, removed panels and lower of the 2 motors and installed new motor, replaced all panels. I now have to check to make sure it is turned on it is so quiet! We lived with this noise so long because the appliance repair people said it was very expensive, about $400.00 to replace the motor, we did it for under $100.00 !!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Tom from Fallston, MD
Parts Used:
WP9759243
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
oven would not heat up in bake or broil
Removed oven from the wall. Take off back panel. Removed thermal overload thermostat. Replaced with new part and works great.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Phil from Flemington, NJ
Parts Used:
WP4449253
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Broken inner glass in oven door
Like others said, the trick was getting the oven door off. If you don't have the instructions, here's how: Open the door all the way. Shine a flashlight on the hinge, and you will see an open hole about 3/16" diameter below the hingepin and toward the oven. With the door open, put a 5/32" allen wrench or any other comparably-sized metal pin into the hole in each hinge. With the pins in place, close the door as far as it will go, which is almost but not quite fully closed. Put one hand under the door handle, the other hand under the bottom of the door, and pull the bottom of the door down and out. With maybe a little wiggling, it will come right out. That's really all there is to it! Taking out all the glass layers is straightforward; you don't need any instructions to see how to do it.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Christina from West Des Moines, IA
Parts Used:
WP8203546
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
range installer broke a screw off & busted the plastic piece
Had to screw off old terminal block & screw on new one
Was this instruction helpful to you?
Thank you for voting!
Customer:
Stephen from Santa Rosa, CA
Parts Used:
WP4449253
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Interior oven glass cracked
The only difficult part of this repair was figuring out how to get the oven door off. Most instructions advise you to flip the hinge locking clips, then lift off the door. But this oven does not have hinge locking clips. What it has is holes in the hinges, just behind the hinge pins. To get the door off, you need to open the door and insert some 3/16' pins in those holes, then close the door and lift it off. I almost got this right the first time, but I used 1/8" pins, and they didn't work, too small. It took me a long time to figure out to use bigger pins. Once the door is off, it's just a few Philips screws to work your way down to the glass. There are 4 layers of glass in this door.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Tom from Rancho Murieta, CA
Parts Used:
WP4449253
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
Replacing the interior oven door glass was the easy part. I'm still struggling with getting the hinges on the door to reinstall. Following all the installation instructions, but they still won't stay in place and door keeps coming out from frame.
By reversing the way I removed the door hinges from the frame, per the reinstall instructions. I called the 800# and they emailed me a diagram, but the hinges depicted were different than mine. When my back feels better, I'll keep trying.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bruce from Des Moines, IA
Parts Used:
WP9759243
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Oven would not heat after self cleaning operation
Removed trim strip from each side of oven, removed one screw from each side hat held oven in place and slid oven out of wall. Finally found the thermostat located on the back side of the oven after removing the sheet metal on back. replaced the thermostat and reversed the procedure. Only difficult part was locating the thermostat. I thought it was on top, when in fact it was on the back. Pretty easy, really, and saved some cash in the process.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rod from Dripping Springs, TX
Parts Used:
WP9759243
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
No operation after cleaning
re thermostat/fuse breakage after cleaning: I replaced the part a 2nd time within a year, both times after a cleaning cycle and after 10 years of no similar problem . This time, when putting the oven back, I cleaned all around the door frame and noticed the exhaust grill was heavily filled with dust strands. It's possible this reduced the exhaust enough to overheat the oven during long high temp cleaning and blow the thermo fuse. Just a thought.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Larrt from Minooka, IL
Parts Used:
W10642989
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Microwave turntable stopped rotating.
1. Unplug the power cord from the wall socket. 2. Remove the 10 screws holding the bottom cabinet cover in place. The bottom cabinet cover will swing down allowing acces to the inside ofe the microwave. 3. Remove the connector from the turntable motor. 4. Use a T15 Torx driver to remove the 2 Torx screws holding the motor in place. 5. Remove the motor. 6. Reverse the process using the new motor.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rubie from Elgin, SC
Parts Used:
WP9759243
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
No Heat After Self Cleaning
Turned the circuit breaker off, removed trim and the oven screws, pulled oven out, and placed on a stand in front. Electrical cord was just long enough without disconnecting. Removed the back panel, installed the old thermostat with the new one the same way. Used the same phillips screwdriver for the operation. Installed the oven using reverse order. Turn circuit breaker on, back in business. Prior comments definitely helped me a lot. Thanks.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Don from El Dorado Hills, CA
Parts Used:
WP4449253
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Replace interior oven glass
I followed these instructions put in by a fellow customer. These were very helpful. Just make sure the glass is finger print free before you put it all back together. My time was 30 minutes end to end. =========================== The first thing I did was to remove the oven door by releasing the two latches on the hinges (by hand). I then raised the door toward the vertical position and lifted up. The hinges slide out of the oven housing. I laid the door, inside face up on my island counter top. This ensures that none of the parts will fall when disassembling the door. Next I unscrewed the screws 4 top and bottom and four on the inside face. This releases the frame from the front housing. Lift the frame off the door, exposing the glass pieces. Lift off the broken inside glass and place the new piece in the glass retaining housing. Replace the outside frame and replace all screws. Take door back over to oven and slide hinge bottoms back into slots on oven. Rotate to horizontal position and flip latches back to locked position. Total time was about 10 minutes mainly because I was curious how the door was constructed and I poked around while it was disassembled
Was this instruction helpful to you?
Thank you for voting!
Customer:
Tim from Charlotte, NC
Parts Used:
4448937
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
The Inner oven door glass was cracked
To remove the oven door, you have to slide 2 small nails into the holes in side of the hinges. When you then close the oven door, the nails force the hinges out of the oven box, and the door comes off. Lay the door on a cloth face down, and remove the phillips screws around the perimeter. The door comes apart in layers, with more screws and layers of glass inside. Lay in the new glass, and reassemble. Carry the door over to the oven and push the hinges in hard at the bottom. Lay the door flat to remove the nails. Close the door. Job done.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the KEMS377GBL4
121 - 135 of 152