KBMC147HWH03 KitchenAid Microwave Oven Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from Dunn Loring, VA
- Parts Used:
- W11373838
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Chipped glass serving tray in microwave
Lifted out the chipped one, inserted the new one. Pretty simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Sarasota, FL
- Parts Used:
- WP8203546
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
circuit breaker blew
I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Alpharetta, GA
- Parts Used:
- WP4452398
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Right torsion spring on microwave door broke for 4th time
Broke again - same spring - 4th time, maybe 10 years old. Last break/fix was October 2010, so got just a little over 2 years out of a new one. Only me and my wife, so not like it's 5 wild kids and their friends attacking the door. Just a bad design, it seems. But, see my earlier instructions - every time this happens, I order new part, print out my old instructions, wait a day or so for part to arrive (really quick this time - asked for 3-5 days delivery, got part in just 1!!! Way to go PartSelect!!!!), then repair in 25-30 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larrt from Minooka, IL
- Parts Used:
- W10642989
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave turntable stopped rotating.
1. Unplug the power cord from the wall socket. 2. Remove the 10 screws holding the bottom cabinet cover in place. The bottom cabinet cover will swing down allowing acces to the inside ofe the microwave. 3. Remove the connector from the turntable motor. 4. Use a T15 Torx driver to remove the 2 Torx screws holding the motor in place. 5. Remove the motor. 6. Reverse the process using the new motor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lyn from Sonoma, CA
- Parts Used:
- W11373838
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replaced broken glass cooking tray
I took the new try out of the box and placed it on the turntable and I was DONE! Took about 10 seconds. The delivery was speedy as promised. I will definitely order from this company again for replacement parts.Very good customer service and communication.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Saba H from Lincolnwood, IL
- Parts Used:
- W10401387
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Outer Glass on microwave cracked
Unscrewed the microwave door, held by 2 screws, near upper edge.The whole panel ie stainless steel plate with glass was removed.The door handle was unscrewed and handle removed.The handle was screwed into the new panel( Stainless steel with glass window)and then slided back carefully into the 2 bottom clips/holders.Holes were aligned and screws put back in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Charlotte, NC
- Parts Used:
- 4448937
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The Inner oven door glass was cracked
To remove the oven door, you have to slide 2 small nails into the holes in side of the hinges. When you then close the oven door, the nails force the hinges out of the oven box, and the door comes off. Lay the door on a cloth face down, and remove the phillips screws around the perimeter. The door comes apart in layers, with more screws and layers of glass inside. Lay in the new glass, and reassemble. Carry the door over to the oven and push the hinges in hard at the bottom. Lay the door flat to remove the nails. Close the door. Job done.
Was this instruction helpful to you?
Thank you for voting!