KEHU309SSS03 KitchenAid Microwave Oven Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ronald from DAVIS, CA
- Parts Used:
- WP9760774
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Center broiler element burned out
Removed oven door for easy access. Removed 4 phillip head screws that held broiler element from top of oven. pulled wires a couple of inches out from back of oven and used flat screw driver to help separate the wires connecting the broiler from the oven. Did the opposite to install the new element,.
The best part of this operation was the fact that the part arrived from Part Select by Fed X the next day after ordering it all for a shipping cost of $8.75. Great Service Highly recommend Part Select.
The best part of this operation was the fact that the part arrived from Part Select by Fed X the next day after ordering it all for a shipping cost of $8.75. Great Service Highly recommend Part Select.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from SOUTHAVEN, MS
- Parts Used:
- WP9760588
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
oven light would not come on
cut power off and placed sturdy table same height as bottom of oven in front of oven. removed trim screws. pulled oven out onto table. removed top cover and panel on left side . tested transformer to be sure it was bad. then replaced transforner
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from ROSWELL, GA
- Parts Used:
- W11724411
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing Part on a Scratch and Dent Microwave
We bought a really nice microwave for about 1/3rd of the MSRP, but it was an open box item and when we got it home we found that it was missing a bracket on the inside of the microwave. We were able to replace the bracket easily thanks to partselect.com.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sam from TINLEY PARK, IL
- Parts Used:
- WPW10131825
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven will not maintain set temp
Remove rear panel - remove sensor from inside - unplug from rear - reverse to install - did not fix problem
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ethan from Concord, MA
- Parts Used:
- WP8304493
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door gasket was worn and torn
I removed the retainer with a screwdriver and pulled the old gasket. Then I installed the new gasket which consisted of pushing the retaining pins into place in the holes with my thumbs. They fit perfectly and the oven looks like new. Excellent.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from CLARKSVILLE, MD
- Parts Used:
- W11373838
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Glass Tray broke
Ordered a new one, put it in place in less than one minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Minden, NV
- Parts Used:
- W11373838
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Glass microwave tray broke
Set the new one inside the microwave
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from SUMMERVILLE, GA
- Parts Used:
- W11373838
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Cracked glass tray
Part arrived in timely manner and placed it in microwave oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from EVANSTON, WY
- Parts Used:
- WPW10131825
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven temperature did match target temp entered on control panel.
I found that what was keeping the old temp sensor electrical connection attached to the stove-side connection was a little tab. It wasn't obvious that that was the thing that was keeping the connection secure but there weren't any other alternatives. So pushing the tab up with the metal probe (just a narrow rigid metal wire) allowed me to pull the connection apart.
All this takes place way at the back of the oven so its difficult to fiddle with a screwdriver and the retaining screws at arms length. Putting a bit of scotch tape around the screw to keep it attached to the screwdriver kept it from falling off. My hand was a bit shaky extended like that so that was the way to go.
Bottom line, if your oven won't reach or hold the temp you dial in on the control panel it's the temperature sensor. Now if I set it for 300 deg. that's what I get.
All this takes place way at the back of the oven so its difficult to fiddle with a screwdriver and the retaining screws at arms length. Putting a bit of scotch tape around the screw to keep it attached to the screwdriver kept it from falling off. My hand was a bit shaky extended like that so that was the way to go.
Bottom line, if your oven won't reach or hold the temp you dial in on the control panel it's the temperature sensor. Now if I set it for 300 deg. that's what I get.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Felix from GREER, SC
- Parts Used:
- W11724411
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The grill support, which is installed on the ceilling inside the microwave broke
The part is pushed against the ceiling into an opening and then turned 90 degree. That is is.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from BISMARCK, ND
- Parts Used:
- WP9760774
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver
Baking element failed
Remove the oven from the wall
Remove the rear panel
Remove the 2 bottom panels
Lift and fold back the insulation
Remove the element enclosure
Replace the element
Reverse the steps to assemble
* the oven would not preheat and the top elements were working
Remove the rear panel
Remove the 2 bottom panels
Lift and fold back the insulation
Remove the element enclosure
Replace the element
Reverse the steps to assemble
* the oven would not preheat and the top elements were working
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stephen from middleboro, MA
- Parts Used:
- WP4452164
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
change bulb
removed double wall oven light lens install bulb replace lens fini
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from LYMAN, ME
- Parts Used:
- W11373838
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Open the carton and install turntabe glass tray.
Fool proof.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from HEMET, CA
- Parts Used:
- W11373838
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken glass tray
Just put it in
Was this instruction helpful to you?
Thank you for voting!
Old oven rack was not possible to clean any more
Order part from this site was very easy. It matched perfectly and I had no problem installing it
Was this instruction helpful to you?
Thank you for voting!