KEMS308SWH05 KitchenAid Microwave Oven Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Carolyn from BURLESON, TX
- Parts Used:
- W10886919
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Bulb entirely to small and unopened
Should be about 1 5/8 inch with 3/8 inch prongs. Sent bulb won’t fit.
JennAire book showed
Part 74004458-halogen bulb part PS 11765655 was substituted.
I paid additional shipping so my son could install when here. My husband and I are 79 and unable to bend into the oven.
I need the correct part
where do I return the unopened $29.95 bulb for credit on my card and receive the correct one?????
Carolyn Sanders 817-319-6581
Order 21938961
JennAire book showed
Part 74004458-halogen bulb part PS 11765655 was substituted.
I paid additional shipping so my son could install when here. My husband and I are 79 and unable to bend into the oven.
I need the correct part
where do I return the unopened $29.95 bulb for credit on my card and receive the correct one?????
Carolyn Sanders 817-319-6581
Order 21938961
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Minden, NV
- Parts Used:
- W11373838
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Glass microwave tray broke
Set the new one inside the microwave
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from SUMMERVILLE, GA
- Parts Used:
- W11373838
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Cracked glass tray
Part arrived in timely manner and placed it in microwave oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Felix from GREER, SC
- Parts Used:
- W11724411
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The grill support, which is installed on the ceilling inside the microwave broke
The part is pushed against the ceiling into an opening and then turned 90 degree. That is is.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from EVANSTON, WY
- Parts Used:
- WPW10131825
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven temperature did match target temp entered on control panel.
I found that what was keeping the old temp sensor electrical connection attached to the stove-side connection was a little tab. It wasn't obvious that that was the thing that was keeping the connection secure but there weren't any other alternatives. So pushing the tab up with the metal probe (just a narrow rigid metal wire) allowed me to pull the connection apart.
All this takes place way at the back of the oven so its difficult to fiddle with a screwdriver and the retaining screws at arms length. Putting a bit of scotch tape around the screw to keep it attached to the screwdriver kept it from falling off. My hand was a bit shaky extended like that so that was the way to go.
Bottom line, if your oven won't reach or hold the temp you dial in on the control panel it's the temperature sensor. Now if I set it for 300 deg. that's what I get.
All this takes place way at the back of the oven so its difficult to fiddle with a screwdriver and the retaining screws at arms length. Putting a bit of scotch tape around the screw to keep it attached to the screwdriver kept it from falling off. My hand was a bit shaky extended like that so that was the way to go.
Bottom line, if your oven won't reach or hold the temp you dial in on the control panel it's the temperature sensor. Now if I set it for 300 deg. that's what I get.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from ELKTON, OR
- Parts Used:
- WP9760774
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
burnt out element
good, used tie wire with a hooked end to fish one wire out of the back, to keep from removing the oven
Was this instruction helpful to you?
Thank you for voting!
Broiler quit broiling
Turned off circuit breaker to oven
Removed oven door
Removed screws of reflector plate and top and back of oven
Gently pulled element out and down slightly
Removed slide crimps on wires
Replaced reflector plate on new element
Connected slide crimps on wires
Screwed reflector plate with new element to top and back of oven
Done. Total time 22 minutes
Tested and it’s perfect!
Removed oven door
Removed screws of reflector plate and top and back of oven
Gently pulled element out and down slightly
Removed slide crimps on wires
Replaced reflector plate on new element
Connected slide crimps on wires
Screwed reflector plate with new element to top and back of oven
Done. Total time 22 minutes
Tested and it’s perfect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from BISMARCK, ND
- Parts Used:
- WP9760774
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver
Baking element failed
Remove the oven from the wall
Remove the rear panel
Remove the 2 bottom panels
Lift and fold back the insulation
Remove the element enclosure
Replace the element
Reverse the steps to assemble
* the oven would not preheat and the top elements were working
Remove the rear panel
Remove the 2 bottom panels
Lift and fold back the insulation
Remove the element enclosure
Replace the element
Reverse the steps to assemble
* the oven would not preheat and the top elements were working
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lewis from WICHITA, KS
- Parts Used:
- WP9760774
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven upper heating element went out.
Turned the breaker off to the stove.
Removed 4 screws holding the element in place.
Disconnected the electric connection from element.
I had to replace the screws which were corroded.
Connect the new element electric connection.
Replace the 4 screws.
Turn on the power.
Turn on oven to burn off the smell of the new element.
You are done.
Removed 4 screws holding the element in place.
Disconnected the electric connection from element.
I had to replace the screws which were corroded.
Connect the new element electric connection.
Replace the 4 screws.
Turn on the power.
Turn on oven to burn off the smell of the new element.
You are done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from HEMET, CA
- Parts Used:
- W11373838
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken glass tray
Just put it in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from LYMAN, ME
- Parts Used:
- W11373838
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Open the carton and install turntabe glass tray.
Fool proof.
Was this instruction helpful to you?
Thank you for voting!
Old oven rack was not possible to clean any more
Order part from this site was very easy. It matched perfectly and I had no problem installing it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kristen from Yorba Linda, CA
- Parts Used:
- W11373838
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Missing turntable
Ordered the part and was extremely pleased with how quickly it shipped and also the packaging was extremely secure. Will definitely purchase from this site again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from MIAMI, FL
- Parts Used:
- W10660052
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Micro Wave Steamer
I spoke to Daily via the phone and I ordered a new steamer since my original steamer cracked over a period of time. No installation, no problems I just recently used it and works perfectly! Thank You!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from Conyers, GA
- Parts Used:
- W11724411
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The ceramic hanger that holds up the element for the convection over broke
Took about 10 seconds... turn the new ceramic holder sideways, push up in the hole, bring the element up to position and twist the ceramic piece 45 degrees into place to hold element. That's it!!! Very simple....
Was this instruction helpful to you?
Thank you for voting!