KEMS308SSS02 KitchenAid Microwave Oven Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- frank from Wilmington, NC
- Parts Used:
- WPW10131825
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
All elements would heat to around 200 degrees, then stop
Disconnect the sensor harness and checked resistance on the sensor,should read around 1100 ohm I only got 25.The sensor is mounted in the oven cavity back wall below upper element,the door must be removed. Unscrew 2 Philips head screw,unhook the harness,install new sensor,reconnect harness,install screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Minden, NV
- Parts Used:
- W11373838
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Glass microwave tray broke
Set the new one inside the microwave
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from SUMMERVILLE, GA
- Parts Used:
- W11373838
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Cracked glass tray
Part arrived in timely manner and placed it in microwave oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Felix from GREER, SC
- Parts Used:
- W11724411
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The grill support, which is installed on the ceilling inside the microwave broke
The part is pushed against the ceiling into an opening and then turned 90 degree. That is is.
Was this instruction helpful to you?
Thank you for voting!
Broiler quit broiling
Turned off circuit breaker to oven
Removed oven door
Removed screws of reflector plate and top and back of oven
Gently pulled element out and down slightly
Removed slide crimps on wires
Replaced reflector plate on new element
Connected slide crimps on wires
Screwed reflector plate with new element to top and back of oven
Done. Total time 22 minutes
Tested and it’s perfect!
Removed oven door
Removed screws of reflector plate and top and back of oven
Gently pulled element out and down slightly
Removed slide crimps on wires
Replaced reflector plate on new element
Connected slide crimps on wires
Screwed reflector plate with new element to top and back of oven
Done. Total time 22 minutes
Tested and it’s perfect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from EVANSTON, WY
- Parts Used:
- WPW10131825
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven temperature did match target temp entered on control panel.
I found that what was keeping the old temp sensor electrical connection attached to the stove-side connection was a little tab. It wasn't obvious that that was the thing that was keeping the connection secure but there weren't any other alternatives. So pushing the tab up with the metal probe (just a narrow rigid metal wire) allowed me to pull the connection apart.
All this takes place way at the back of the oven so its difficult to fiddle with a screwdriver and the retaining screws at arms length. Putting a bit of scotch tape around the screw to keep it attached to the screwdriver kept it from falling off. My hand was a bit shaky extended like that so that was the way to go.
Bottom line, if your oven won't reach or hold the temp you dial in on the control panel it's the temperature sensor. Now if I set it for 300 deg. that's what I get.
All this takes place way at the back of the oven so its difficult to fiddle with a screwdriver and the retaining screws at arms length. Putting a bit of scotch tape around the screw to keep it attached to the screwdriver kept it from falling off. My hand was a bit shaky extended like that so that was the way to go.
Bottom line, if your oven won't reach or hold the temp you dial in on the control panel it's the temperature sensor. Now if I set it for 300 deg. that's what I get.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from ELKTON, OR
- Parts Used:
- WP9760774
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
burnt out element
good, used tie wire with a hooked end to fish one wire out of the back, to keep from removing the oven
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from BISMARCK, ND
- Parts Used:
- WP9760774
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver
Baking element failed
Remove the oven from the wall
Remove the rear panel
Remove the 2 bottom panels
Lift and fold back the insulation
Remove the element enclosure
Replace the element
Reverse the steps to assemble
* the oven would not preheat and the top elements were working
Remove the rear panel
Remove the 2 bottom panels
Lift and fold back the insulation
Remove the element enclosure
Replace the element
Reverse the steps to assemble
* the oven would not preheat and the top elements were working
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lewis from WICHITA, KS
- Parts Used:
- WP9760774
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven upper heating element went out.
Turned the breaker off to the stove.
Removed 4 screws holding the element in place.
Disconnected the electric connection from element.
I had to replace the screws which were corroded.
Connect the new element electric connection.
Replace the 4 screws.
Turn on the power.
Turn on oven to burn off the smell of the new element.
You are done.
Removed 4 screws holding the element in place.
Disconnected the electric connection from element.
I had to replace the screws which were corroded.
Connect the new element electric connection.
Replace the 4 screws.
Turn on the power.
Turn on oven to burn off the smell of the new element.
You are done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from HEMET, CA
- Parts Used:
- W11373838
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken glass tray
Just put it in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from LYMAN, ME
- Parts Used:
- W11373838
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Open the carton and install turntabe glass tray.
Fool proof.
Was this instruction helpful to you?
Thank you for voting!
Old oven rack was not possible to clean any more
Order part from this site was very easy. It matched perfectly and I had no problem installing it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Fernandina Beach, FL
- Parts Used:
- W11724411
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken mounting bracket for coils in convection microwave.
Very easy, fit perfectly.No tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from LAKEVILLE, MN
- Parts Used:
- W11724411
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grill support broke. Sounds like a common problem based on other’s comment.
Turn the grill support 90 degrees to the opening in ceiling of micro. Insert then turn back 90 degrees so the support is in-line with the slot. Hang the wire on the support. Hours of worry over what this was gonna cost me to get repaired, then a 45 second fix costing only 29 bucks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from Conyers, GA
- Parts Used:
- W11724411
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The ceramic hanger that holds up the element for the convection over broke
Took about 10 seconds... turn the new ceramic holder sideways, push up in the hole, bring the element up to position and twist the ceramic piece 45 degrees into place to hold element. That's it!!! Very simple....
Was this instruction helpful to you?
Thank you for voting!