6654438996 Kenmore Microwave Oven Combo - Instructions

removed two screws applied new part replaced two screws

Could not believe that the part was here the next day! Install was simple,just connect the wires and screw it in.

With a phillips head screw driver we removed 2 screws pulled out the element about 3 inches and disconnecte the two wires from the insulated connection put the new element in replaced the element in the wall of the oven and replaced the 2 screws. Started the oven and we were good to go.

Part ordered on Monday, delivered on Thursday, put in on Thursday and cooking in no time. Very satisfied customer.
Thanks.

First I removed the two screws that hold the element in place with a 2' Phillips Head. I then pulled the element out about 3 inches and disconnected the two wires, with nose pliers, since they were semi-hard to remove the male from the female terminals.
I placed the order over the computer and it arrived in 2 days.
I was very pleased with PART SELECT.

Grabbed my courage with both hands, then with my other hand I used a screwdriver. Delicately removed 2 screws holding the broken element. Once that delicate operation was done, I took out the old and place the new. Once again grabbed the screwdriver and with agility replaced 2 screws. Then, I turned on the oven and Voila, ready to bake some enchiladas.
Winner, winner, chicken dinner.

Backed out two screws, disconnected two wires from faulty element, connected wires to new element, screwed back into place. (New element was ordered by phone and received the next day.)

Turn off the oven's breaker. Remove oven grates. Unscrew two screws holding in the bake element. Slowly pull the bake element out a few inches. Using pliers, CAREFULLY unattach the connectors from the ends of the bake element. DO NOT FORCE OR CRUSH THE CONNECTORS. Using your hands only, attach the connectors to the ends of the new bake element. Re-insert the element into the back of the oven. Re-insert the screws to attach the new element to the back of the oven. Turn the breaker back on. Turn the oven on bake to test the element. Go have a beer to congratulate yourself on saving $75 or more. Should take about 10 minutes if you're proceeding slowly & carefully. It'll take 2 minutes if you're reckless and get lucky, but it'll take 2+ hours if you're reckless and all goes wrong, causing you screw up the connectors and need to go buy some plus crimpers, etc.

Used screwdriver to unfasten the old element from the oven frame. Then unplugged the two wire plugs from the back of the old element. Reversed the process to install the new. Couldn't have been any simpler.

First I made sure it was in fact the lower bake element that was broken. I turned the oven on & noted the element did not glow red. I also used a laser thermometer to verify the element was at "room temperature" for the room it was in (the oven - about 200 degrees, given what the upper bake element was contributing.)
And close visual inspection showed that a section of te bake element had melted thru where something had recently spilled onto it.
Swapping it out was easy - turn off the electrical breaker controlling the oven, unscrew the bake element, disconnect the electrical contacts to it (which required pliers, since they had been on a Looong time, and a little care to not use the pliers too hard & thus break the wires or contacts), then reverse the process to install the new element.

It works great now.

Very easy, thanks for the great support

Unplug oven unit from outlet or flip the breaker to disconnect the electricity. Used screwdriver to remove face cover, pulled wire connections from posts of old bake element. Attached wire connections to posts of the new bake element(they just slip on the posts). Aligned the face cover flush with the oven wall and replaced screws to hold cover on. Reconnect electricity and ready to bake. It is very simple.... We were very pleased with how quickly the element was delivered after ordering it.

I just removed two screws and disconnected the push on clips I then cleaned the botton of the oven and replaced the element. And it works just like new.

removed racks and door (could have left door on but made it easier to reach screws) removed 2 screws from old element unplugged the 2 wires and reversed process for new element.

I unscrewed the two screws holding the element in place and disconnected the two wires. Removed the element from the oven and replaced with the new one. Plugged in the two wires and replaced the two screws that secures the element to the back of the oven. Turned on the oven to test and turned back off when satisfied everything was O.K. Easy job.

Removed 2 screws on heating element mount plate. Pulled out heating element 3 inches and used needle nose pliers to remove the 2 connector clips. Reconnected connector clips by hand to new heating element. Put heating plate back into original position and reinstalled 2 mount screws.