Models > 91147813200 > Instructions

91147813200 Kenmore Microwave Oven Combo - Instructions

Jump to:

All Instructions for the 91147813200
31 - 45 of 172
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Don from Monte Sereno, CA
Parts Used:
WB24X829
Difficulty Level:
A Bit Difficult
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Microwave wouldn't start after "Start" pushed
Took cover off, noted the two side by side switches easily visible and we hought one of these was responsible. Then son noted a third switch at the top of the plastic assembly which inserts at an odd angle. When it was inspected signs of a previous short showed up with burnt contact points. Reinserted at same odd angle as there were guide holes, closed things up and oven worked 100%. Great prompt service and great website!! We will use you again
11 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Barbara from BELLEVUE, WA
Parts Used:
40A15
Difficulty Level:
Very Difficult
Total Repair Time:
Less than 15 mins
Twice I ordered the oven light bulb & each time the light bulb was defected
I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance
14 of 23 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
PATRICK from Covington, LA
Parts Used:
WB24X829
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Oven blows 20 amp fuse
Primary door switch was shorted and blew the fuse when the oven was plugged in. Replaced primary door interlock switch.
12 of 18 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
noreen from flushing, NY
Parts Used:
WB48T10095
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Needed extra oven space
Thanksgiving was coming and I needed extra oven space. So I ordered an additional rack. Installation ... just put it in the oven. My part came the day after I ordered it.
11 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
JULIA from JACKSONVILLE, FL
Parts Used:
WB24X829
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
microwave would not start
took of cover removed switch and replaced with new one
11 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Micheal from SHEPHERDSVLLE, KY
Parts Used:
WB56T10105
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Inner oven door glass broke
Pull the old one put in the new one ... took about 20 minutes
9 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Larry from CHARLOTTE, NC
Parts Used:
WB24X830
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
When you open the door at the start the fan wood come on
I removed the unit from the wall removed the top two screws holding the panel above the door I the two screws holding the control panel removed the three switchs I found the top one to be blown and replaced it
8 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Charles from OAKDALE, NY
Parts Used:
WB24X830, WB24X829
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Microwave stays on when door opened
Removed control panel first then removed bracket holding door switches 8 screws total very easy fix ????
8 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
hazel from Martinsburg, WV
Parts Used:
WB06T10012
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Carousel would not turn
Popped broken assembly off, slid new on onto shaft. Took more time to open the box than to fix the microwave.
8 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Frank from VIPER, KY
Parts Used:
WB27X10928
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Blown fuse in microwave
One small Phillips screwdriver and one fuse puller (I used cord). Unplug unit. Remove the two screws on the vent face plate. Remove the one screw on the panel assembly. Gently let hang. Pull the fuse located on the upper left wall. Replace fuse. Reassemble.
8 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
garry from manhattan, IL
Parts Used:
WB23T10015
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
f2 and f3 codes oven would shut off
lift door off and remove racks take out old sensor. one word of advise when pulling old sensor out tie a string around connector coming out of oven if it slips out of yor hand it could fall through hole iif you dont have a string attached you pull the whole oven out of wall to acess it
7 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ken from WARE, MA
Parts Used:
WB24X830, WB24X829
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Microwave powered up when door was opened
After researching on line and watching installation videos, ordered all three switches and installed. Disassembly of microwave was simple, removing the bracket holding the switches was a little tricky, it sits behind a metal post and you have to angle and wiggle it out. One note of caution when replacing all three switches, be sure to install correct switch in correct location. Had two of one style switch and one of a second style, and put one in wrong place, causing microwave to power up again when door was opened. After thinking it through and doing a second disassembly, and double checking installation instructions, corrected problem and microwave now works fine.
7 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Patricia from Amarillo, TX
Parts Used:
WB41T10003
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
When we bought the house the gasket was hard from food deposits
Just pulled out the old one and pushed in the new one. Very easy. I was afraid to run this self-cleaning oven until I installed the new gasket. It worked perfectly.
7 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Howard from Rio Vista, CA
Parts Used:
WB08T10002
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Oven light did not work
Turned off power to the oven, Removed the oven light housing, installed new housing, turned power on and walla.
9 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joseph from Beaumont, CA
Parts Used:
WB44T10043
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Broken Bake Element
I unfastened the three 1/4" rear screws, then the two support screws on top. I pulled the old element out,( plenty of slack wire luckily). disconnected it from the bayonet-type connections, then attached the new element. I secured the new element using the 1/4" screws. Bingo!
6 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 91147813200
31 - 45 of 172