72169079900 Kenmore Microwave Oven Combo - Instructions

Take cover off microwave. Check door switches to determine which one was faulty.Remove and replace faulty switch.

I looked up my problem on the internet and found a very helpful video. Microwave on video was different brand but the internals and methods were very much the same. The video made it simple and easy to fix. Found the replacement switch on the LG parts site and ordered. Two different switch types. One with red switch, the other green. Part was $7.28. Saved a bundle in service costs. Here is the repair video.

https://www.youtube.com/watch?reload=9&v=_AglBJoHgDs

i unplugged the unit,unscrewed the outer shell so that all the wiring and internal components were visible.starting at the first of three micro switches i removed the slip on terminals installed the alligator clips too the wires so the switch would now be bypassed.i made sure the wires and clips were not touching anything plugged unit in and it worked.i then installed the new switch and closed up the outer shell

Remove the rear casing of the microwave using both a Phillips head screw driver. The lower rear screws require a star shaped bit with a hole in the middle (security bit). Once the rear casing is removed, it is very easy to access and replace the bulb. But the bulb sent was NOT identical to the original which has a straight fitting into the receptacle. The one sent had a fitting with a 90 degree. The bulb did not quite fit in place, but I secured it with some black electrical tape.

Problem was due to a faulty door switch. Replaced with a new switch and the microwave now works fine! Only thing that was tricky was that LG uses the hex screws with a peg in the middle to keep the microwave cover on. Had to use a small screwdriver and pliers (on the screwdriver) to unscrew the screws.

Easy, and the microwave still doesn't work.

Take off cover then the bottom. Transformer is on the bottom plate and wires won't let it come all the way off, too many wires to pull off so will have to position the bottom plate so you can get to the motor. Remove 1 screw on motor and remove motor. Install new motor connect wires replace bottom plate, replace cover. All done (hope & pray it works ok) mine worked perfect. Hope this helps.

Unplug.Take off the external cowling from the back of the unit by removing the torx security screws. Tip: instead use a thin screwdriver blade to unscrew the torx screws, or knock out the center pins of these screws. Remove the bottom panel. The replacement motor is attached with one phillips screw, re-attach wires to motor - polarity doesn't matter. Re-assemble and you're finished.

Pried cover off bottom-center of microwave. It seems to be either glued or lightly tack welded. Removed 2 small Phillips screws to remove motor. Disconnected electric feed by hand. Don't let go of electric wire or small screws. They will be hard to retrieve from behind the rest of the metal base. Reverse process to install new motor. Didn't try to put small cover back on.

Overall repair quite simple. Removed screws from the sides and rear of the microwave, then removed cover. Next, removed only the screws to separate the bottom cover. Removed the one screw in the AC Synchronous motor to remove the motor (had to use small screwdriver through a vent slot in the bottom to remove the screw). Unplugged and removed motor. Installation is the reverse of removal. Note: on the back of my appliance were 4 torx screws with a tamperproof pin in the center. I used the rotary tool to grind out the pins so I could use a regular torx bit instead of ordering specialty bits.

Eight screws off the bottom exposed the cover plate. Easily found the motor location the looked up the item number and verified data and ordered the part. Replaced the motor, tightened the screws and flipped it upright. Plugged it in and the lights came on. Set a time pushed start and smiled! The eagle had landed!!!!

I removed the outer cover of the microwave and removed the bottom palte to access the small motor. i unplugged the old motor from teh wiring connector, removed (1) screw and motor came out. I reversed the proceedure with the new motor and it was finished.It was a piece of cake.