91141485890 Kenmore Microwave Oven Combo - Instructions

Took back panel off unplugged sensor and replugged in and worked like a charm!Sears wanted $400 and was going to 'overrepair"Got the 60 dollar part on here. UPS shipped to wrong address and customer service refunded my shipping and was excellent! would definetly use again!thanks

Before you get started on this be sure that you already have the Bottom Cabinet Trim Assembly (item #PS952490) either ordered or installed. We were not aware that you had to order both trim items separately which meant we had to remove the oven door twice. Using the screwdriver to pull back the door tabs, we first removed the oven door. The trim installed very easy. We just lined up the holes, pushed in, and then down on the trim to lock it in place. When reinstalling the oven door, be sure that door latches are almost fully extended before reinserting them into their slots.

Replaced the fuse. Result; did not fix the problem.

Replace the fuses

Replaced the Oven light housing. Unscrewed the two screws that hold the housing in place. Pulled out the housing and disconnected the wire tabs from the light housing tabs. Slid the wire tabs onto the tabs of the new light housing fixture. (Each tab is fitted to the tab in goes on so they can not be mixed up) Pushed the housing fixture back into place and screwed the housing into place.

My unit is built into the cabinets in my kitchen. Only needed to remove 4 screws from inside oven door. Slid out unit. Disconnected old element and connected new one. Reinstalled 4 screws. That was it! Couldn't have been easier.

Feedback on site warned me that broiler element is only connected to oven wiring with press-on spade lugs rather than screws. Even with care I managed to 'lose' a wire and had to retrieve it with section of stiff coat-hanger wire bent into a hook. Coming off that experience, I soldered the spade terminals together before reassembly to avoid a repeat. New element, however, failed to rectify problem. Professional technician found main control unit defective -- a $300 part including installation, but at least GE still has it available. My advice to others in this situation is to remove old element before ordering a replacement, and test with meter to see if it's defective. It may or may not be worth going beyond an element replacement to you.

The part was just like the old one and would have been an easy fix except our range suffered from a lighting hit. The clips had melted together. Called a dealer and asked about a new wiring harness. He said in those cases just cut the clip off and hard wire with wire clips,or firecrackers. We used wire nuts and taped all together and the oven works just great. Nothing is ever as easy as it should be.

I shut off power to the microwave, discharged the Hi-voltage capaciator and disconnected the wires to it, then removed the screw and bracket that held the capaciator in place. After removing and replacing the capaciator, reattaching wires and mounting bracket, and replacing the 15amp fuse, the microwave woked fine.

This repair was quite a bit more difficult then what had been described on the web site. First off, I have a double wall oven that is built in. Sliding it out of the cabinet was difficult and because oven was hard wired, I had to disconnect the actual wiring from the oven back. . Positioning the oven and allowing for it to rest on a support bench was the most difficult part The oven is heavy. Eventually, removing the back and top panels of the oven revealed the sensor connection. I was then able to feed it through the oven and reconnect all the wiring harnesses.. Getting the oven back in the cabinet was equally a challenge. But it did seem to fix the problem with over heating.

First unplugged the microwave, took top grill off, took control panel off, took wires off and used color coded tape to make sure they went back in right places, took fuse out and replaced it and put every thing back and it all worked fine and to top it off my wife did it all. So it was pretty easy.

I opened oven and pushed oven rack inside.

Just like the directions said. Very simple.

After reading reviews that there was no power what so ever and a fuse replacement will solve the problem, I tried it. Replacing the fuse is very easy (and I am not handy at all). All you have to do is remove the microwave cover from the top by removing two screws, slide the cover to the left and pulling the cover off. Then remove the grill in front of you, by removing one or two screws. The fuse is in front of you, use pliers and be firm but gentle. Replacing the fuse is easy but it did not solve my problem.

PartSelect had helpful repair instructions on-line which made the repair easier and faster. Unfortunately, there were other problems with the oven that immediately blew the new fuse I had just installed. It was then determined that additional repair would most likely cost almost as much as a new microwave.