Models > 91147814201 > Instructions

91147814201 Kenmore Microwave Oven Combo - Instructions

Jump to:

All Instructions for the 91147814201

Customer:: Douglas from Thornton, CO
Parts Used:: WB08T10002
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Socket set

Oven lights were burning out regularly

Replaced the Oven light housing. Unscrewed the two screws that hold the housing in place. Pulled out the housing and disconnected the wire tabs from the light housing tabs. Slid the wire tabs onto the tabs of the new light housing fixture. (Each tab is fitted to the tab in goes on so they can not be mixed up) Pushed the housing fixture back into place and screwed the housing into place.

Was this instruction helpful to you?

Customer:: Marilyn from Auburn, WA
Parts Used:: WB41T10003
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

gasket replacement

Took about 15 minutes to take the old one off and put the new one on. Not difficult at all.

Was this instruction helpful to you?

Customer:: Jim from Hyrum, UT
Parts Used:: WB44T10043
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Socket set

Broiler heating element was not working

Turned off the circuit breaker. Removed 5 screws. Unplugged the heating element and then plugged in the new one and replaced the 5 screws. Very simple.

Was this instruction helpful to you?

Customer:: Robert from SANTA MARIA, CA
Parts Used:: WB44T10043
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver

Broiler Element Repair

I was attempting to replace the broiler element on the oven, but I discovered that the wiring may be the actual problem. I suggest before you order parts for a broiler repair, that you test the wires to ensure that you have continuity. I will have to trace the wires back to the source (the other element works fine) and see if I can find the problem with the current. I will keep the broiler element I ordered until I can confirm that the old element works.

Was this instruction helpful to you?

Customer:: Darthy from Dacula, GA
Parts Used:: WB44T10018
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Socket set

Bake element was broken and needed to be replaced

The repair was very simple. In fact the biggest challenge was finding the correct socket set.

Was this instruction helpful to you?

Customer:: Stephanie from Kernersville, NC
Parts Used:: WB27X10928
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers, Screw drivers

microwave won't heat

bought a fuse but that didn't solve the problem. Guess I need a new microwave

Was this instruction helpful to you?

Customer:: Abid from Cross River, NY
Parts Used:: WB03T10211
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

The push button on the microwave would not align

Opened the control panel removed the push button and installed the new one. Please make sure to turn the power off from the circuit breaker before opening the panel.

Was this instruction helpful to you?

Customer:: michael from marstons mills, MA
Parts Used:: WB44T10018
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver

Lower heat element burned out

Very easy, only small issue was the holes for the two self taping screws were a bit high, so I had to drill two new holes to complete repair... Still a very simple repair.

Was this instruction helpful to you?

Customer:: Bradley from Perryville, AR
Parts Used:: WB44T10018
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver

Heating Element

Removed two screws, removed two wires, installed new element. So easy a caveman could do it.

Was this instruction helpful to you?

Customer:: Patrick from Placentia, CA
Parts Used:: WB06T10012
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Turntable does not rotate

A slam-dunk...just replaced the old roller guide with the new one. Simpler than replacing a light bulb and no tools required.

Was this instruction helpful to you?

Customer:: William from Socorro, NM
Parts Used:: WB27X10928
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers, Screw drivers

Quit working

Just like the directions said. Very simple.

Was this instruction helpful to you?

Customer:: MANUEL from ESCONDIDO, CA
Parts Used:: WB27X10597
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

diode burnt

it was a simple screw in on both ends. no soldering

Was this instruction helpful to you?

Customer:: Danny from Glendora, MS
Parts Used:: WB06T10012
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

I had a broken turntable roller quide under the glass plate

opened the microwave door, removed the glass plate, removed the bad roller quide, replaced with the new one, replaced the glass plate and then closed the door. :)

Was this instruction helpful to you?

Customer:: James from Fall Branch, TN
Parts Used:: WB27X10928
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Pliers, Screw drivers

microwave just stopped working

First unplugged the microwave, took top grill off, took control panel off, took wires off and used color coded tape to make sure they went back in right places, took fuse out and replaced it and put every thing back and it all worked fine and to top it off my wife did it all. So it was pretty easy.

Was this instruction helpful to you?

Customer:: andrew from pittstown, NJ
Parts Used:: WB44T10043
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Socket set

Broil element on top oven was not working

Shut the power off at the electric box.Disconnected coil from roof clips.Pulled wire connection from back wall. Disconnected wire clips, connected new unit.Clipped to roof and turned on" Working fine".

Was this instruction helpful to you?

All Instructions for the 91147814201