9119871190 Kenmore Microwave Oven Combo - Instructions

Lifted door off the front of stove, real easy, but heavy, took out old hinge, and replaced with new hinge, I just looked where everything was before, I replaced with new, replaced door back on, and I was finished.

first open oven door a couple inches and slide door up off hinges, then removed storage drawer to gain access to hinge spring, remove hinge spring with pliers noting which hole spring was attached in.then remove three screws from hinge and installed new hinge put three screws in attached spring back and put storage drawer in and oven door back on.

removed oven door, removed drawer under oven, removed three screws holding hinge assembly, unhooked spring from hinge arm, inserted new hinge arm, attached spring, positioned hinge assembly and replaced screws, reinstalled drawer beneath oven being certain that no pot handles interfere with the hinge spring loaded arm, reinstall oven door.

Turn off power at the circuit breaker before working on electric thing.

Removed oven door and shelves for free access to element. Unscrewed the old element, pulled it out, removed the clips and removed the element. Reversed these steps to install the new element. Tested the element to ensure it worked.

Assumed this broken hinge was going to be an expensive service call. Decided to try and fix it myself. Ordered the part off partselect.com and got some repair tips off the website that made this a breeze. I am not handy at all but was able to complete the replacement in less than 30 minutes and spent only $30 on the part. Just needed to unscrew the old hinge and release the spring from under the stove (which I accessed by pulling out the drawer). It would have cost me over $100 to just get a service person to look at it.

It took a nutdriver to remove two nuts. The defective element was removed and the replacement installed. It works great!

Removed the door. Unscrewed the hinge from front of oven. Took broiler drawer out. Unhooked the spring. Removed hinge. Screwed new hinge in. Rehooked the spring. Slid oven door back on hinges. Mission accomplished. Oven door works like a champ. Wife happy.

Basically very easy. Be sure to follow suggested safe practices - DO shut off the circuit breaker to the unit BEFORE starting (I didn't to start with, shorted out the heater leads - dumb on my part). Just removed the burned out element by removing the 2 screws using a nutdriver, pulled the element out, and slipped off the crimp fittings. Reverse steps to install replacement. The crimp fittings were stubborn coming off the old one, so it took longer than expected. Otherwise, easy peasy.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires,held wires one at a time so tehy wouln't slip back into rear holes in oven, slid off connector tabs and pushed on to replacement unit...)

Pull out oven and unplug from 220 outlet. Remove rear upper/lower cover (4 screws), Remove two wires from rear of element. From front, open oven door, remove two screws and pull out old element.
Install new element by reversing above sequence. Then test and push oven back in place. Easy!

Followed the excellent removal and installation video by PartSelect. Also the diagram was excellent allowing me to purchase the correct hinge the first time. Fast shipping.

First turned off the power to the stove at the breaker panel, thenI removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Disconnecting/reconnecting the "clips" was the only difficult part because they did not slip off/on easily. Replaced the element in the oven, replaced the screws...good to go!

Best part of buying from Parts Select was that they shipped the part the same day I ordered it, which was the Friday after Christmas. Competitor would not have shipped till the following Monday and we needed the oven ASAP!

Unscrew the metal rim and remove the glass window. Remove the old bulb by twesting the bulb towards you. Place the new bulb's pins into the slots and twest away from you. Place the metal rims back in place and screw them down.

Cut Wires to old terminal block and wired in new Terminal Block

At first thought I was taking out some insulation but. "Clamp" just slid off and was very easy to install! Finding the right size socket took longer than the repair!