91147794200 Kenmore Microwave Oven Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joe from Harkers Is., NC
- Parts Used:
- WB21X22134
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven slow to heat up
Removed oven door. Removed 2 screws from heat sensor on rear upper wall of oven. Pulled unit out to access rear of unit. Removed six screws on shield on back of unit. Dis connected heat sensor wire and pulled old sensor through from inside of oven. Feed wire of new sensor through from inside and plug in. Everything in reverse. I also had the gas(propane) company come out and check the pressure coming out of the "low pres." regulator. It was low, they changed the regulator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Annapolis, MD
- Parts Used:
- WB21X22134
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
The oven temperature could not be controlled
Disconnect the range from the mains. Open the door. Remove the single screw holding the temperature sensor - this is located on the back wall on center and is screwed to the broiler mounting plate. Remove the four screws holding the boiler element and allow it to hang down on the wire; this exposes a space to feed the wire through later. Now move to the back of the range and remove the six screws that hold the central cover plate. Now push the insulation to up out of the way and you can disconnect the temperature sensor, pull it out through front, insert the new one and connect it. Reassemble in the reverse order. Mine worked perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Abid from Cross River, NY
- Parts Used:
- WB03T10211
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The push button on the microwave would not align
Opened the control panel removed the push button and installed the new one. Please make sure to turn the power off from the circuit breaker before opening the panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Gaithersburg, MD
- Parts Used:
- WB27X10597
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Oven failed to heat food.
Remove the microwave cover. Requires a phillips screwdriver and a torx security bit/nut driver (there are two security type screws on the back...guess they don't want you to do this at home!). I had to buy the a security bit set (about $7). The diode is easily accessible on the right side under the fan. Requires removing on small phillips screw and unplugging on electrical connection. GE provides some instructions in an envelope on top (after cover removed). There is a warning/instruction to discharge the capacitor before service. This was not a problem for me. Actual diode replacement took 30 seconds. Whole job = 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Marcy, NY
- Parts Used:
- WB24T10065
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broken switch
This was a wall mounted oven. Turned off breaker. Pulled panel off by removing 6 screws. Pulled connectors off old switch. Removed old switch. Just a friction fit. I used my jack knife to get it moving. Pushed in the new switch and connected wires. (just push on tabs) Put panel back together and turned on breaker. Done, easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Katy, TX
- Parts Used:
- WB44T10051
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Broiler element burnt out
Unscrewed back plate, unplugged old unit, plugged in new unit and ready to go. Don't forget to turn off circuit breaker for oven before starting !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lynn from sunnyside, NY
- Parts Used:
- WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
F2 reading
Followed the instructions that were sent to me by E-Mail.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- daniel from gap, PA
- Parts Used:
- WB21X22134
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
f-2 or f-3
remove two bolts in on sensor and slip thru back un plug and reverse to put in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BARBARA from FRESNO, CA
- Parts Used:
- WB32T10010
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
The Metal Fasterners Did Not Line Up With The Holes
What I had to do was skip holes,but the more holes I passed over, it did not end up smooth. The gasket is some what wrinkled. If all the holes had lined up it would have taken about 20 seconds. I took it off and on a lot trying to get it smooth. Finally I said well it's just going to be wrinkled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from Kernersville, NC
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
microwave won't heat
bought a fuse but that didn't solve the problem. Guess I need a new microwave
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from MILLER PLACE, NY
- Parts Used:
- WB32T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
worn oven door gasket
simply pry off the old gasket and lay new gasket in place and press pins into slots
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mohammad from Piscataway, NJ
- Parts Used:
- WB27X10928
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Powered Off completely
After reading reviews that there was no power what so ever and a fuse replacement will solve the problem, I tried it. Replacing the fuse is very easy (and I am not handy at all). All you have to do is remove the microwave cover from the top by removing two screws, slide the cover to the left and pulling the cover off. Then remove the grill in front of you, by removing one or two screws. The fuse is in front of you, use pliers and be firm but gentle. Replacing the fuse is easy but it did not solve my problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claudia from Monroe, WA
- Parts Used:
- WB06T10012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Roller Guide
Lifted up the glass plate. Put in the new roller guide. Set the glass plate back in place. Repair done in about 30 seconds! Thanks for prompt service in sending the new part. My only regret is that the part was expensive, and I have already replaced it once before. The new part is still plastic so will probably need to be replaced again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from East China Township, MI
- Parts Used:
- WB27X10928
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
All power to the microwave went out.
PartSelect had helpful repair instructions on-line which made the repair easier and faster. Unfortunately, there were other problems with the oven that immediately blew the new fuse I had just installed. It was then determined that additional repair would most likely cost almost as much as a new microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from Placentia, CA
- Parts Used:
- WB06T10012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Turntable does not rotate
A slam-dunk...just replaced the old roller guide with the new one. Simpler than replacing a light bulb and no tools required.
Was this instruction helpful to you?
Thank you for voting!