JMW9530DAB29 Jenn-Air Microwave Oven Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Tami from Quincy, IL
- Parts Used:
- WP8172138
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I dropped and broke the glass cooking tray
After shopping all over town trying to find a new tray I discovered PartSelect.com, I called and ordered the tray and received it the next afternoon. It couldn't have gone smoother.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Newark, DE
- Parts Used:
- WP8172138
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cooking Glass Tray was broken
EXCEPTIONAL service! WOW! Order it Thursday online and it arrived Saturday. I will definitely use your service again. Thank you again!!
Mr. & Mrs. Charles
Mr. & Mrs. Charles
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Guy from Bellingham, MA
- Parts Used:
- WP59001168, WPR9800486
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Sparks and loud hum from oven
1. I went to the internet to find the service manual for the Maytag microwave.
2. I opened up the oven and started measuring the resistance of the diode, capacitor, transformer, and magnetron between terminals and then to ground. The transformer and magnetron were well within the resistance limits. The diode was shorted in both directions(+-). The capacitor was fully open in both directions -- high resistance.
3. I ordered the 2 parts, installed them, and ran the oven. Worked perfect first time.
4. Reinstalled oven and worked ever since (1 week so far).
5. The secret was that the transformer had a load hum. I figured the transformer was OK. The magnetron had no short between filaments and ground to filaments. The only two left were the diode and capacitor. The first two are about $200 -- almost the value of a new microwave. The $70 repair was well worth it. If the first two were still bad, then tempted to buy a new oven.
2. I opened up the oven and started measuring the resistance of the diode, capacitor, transformer, and magnetron between terminals and then to ground. The transformer and magnetron were well within the resistance limits. The diode was shorted in both directions(+-). The capacitor was fully open in both directions -- high resistance.
3. I ordered the 2 parts, installed them, and ran the oven. Worked perfect first time.
4. Reinstalled oven and worked ever since (1 week so far).
5. The secret was that the transformer had a load hum. I figured the transformer was OK. The magnetron had no short between filaments and ground to filaments. The only two left were the diode and capacitor. The first two are about $200 -- almost the value of a new microwave. The $70 repair was well worth it. If the first two were still bad, then tempted to buy a new oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ansa from Minneapolis, MN
- Parts Used:
- WP8172138
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken cooking tray
I opened the box and put in the new tray, it fit perfectly and I used it that day. Very easy, and convenient.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Bainbridge Island, WA
- Parts Used:
- 4392027
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Microwave worked intermittently depending on how door was closed
Remove top grille (2 screws), undo control panel (1 screw). Tilt down control panel, switches are on the left. There are actually three switches that are involved with the door, two horizontally mounted, one vertically mounted. This would be an EASY REPAIR, but it took me a while to figure out which of the three switches was bad, and also took a while to figure out that there is a plastic rod that inserts through the hole in the switch body. Once i figured this out went like a breeze. Lower horizontal switch was the bad one, but since the kit came with two switches i went ahead and replaced the upper horizontal one as well. IT appears that the horizontal switches are probably more likely to fail than the vertical switch based on the position of the switch and force angles. Works great now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shariq from West Conshohocken, PA
- Parts Used:
- 74003645
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Oven Door Inner Glass Broken
This is fairly easy for anyone to do. First I opened up the front (silver part) of the oven door by removing the screws at the top and the bottom. Then I kept on removing the various layers of glass... the 2 outside ones are removed by removing their respective screws and then you get to the inner-most. These 2 inner ones are in a frame that holds them together. I removed the large silver frame that holds the insulation and the 2-glass-frame in it. Just remove the screws and then tilt the insulation frame out a bit to remove the glass frame. You can tilt the entire insulation holder out but the insulation is soft and it starts to fall off. Just tilting it enough worked for me. Then I opened up the glass frame from one end, removed the left-over broken piece of the old glass pane and installed the new one in. Then reassemble. The entire process is very easy - but you will need another person for a few minutes when you remove /reinstall the glass frame inside the insulation holder. You would just need a little help holding everything... nothing technical. I would rate the repair technicality at 4 or 5/10. It could even be a 3 if there were less steps involved. Good luck! By the way, Amana/Maytag wanted $70 or so for the glass and then the repair fee. I got the part here for about $50.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Decatur, GA
- Parts Used:
- WPW10245259
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench set
Burned terminal block and filter board
Removed and replaced above named parts, rewired.Be sure to tighten all nuts that secure wires. I believe this is what caused the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Marengo, IL
- Parts Used:
- WP8172138
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I broke the glass plate!
Obviously I just placed the new plate in the microwave. What impressed me was the speedy delivery. It only took 2 days. Thanks so much Part Select!
Karen
Karen
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from Milan, OH
- Parts Used:
- WP8172138
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Our glass tray broke in our microwave
Uhh ... I put in the new dish.
However, the service was great. I ordered the dish and it was at my house the NEXT day on a saturday.
However, the service was great. I ordered the dish and it was at my house the NEXT day on a saturday.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TERESA from TROY, NY
- Parts Used:
- WP8172138
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
glass cooking tray broken/turntable not in use
just replacing the glass cooking tray was probably the easiest repair job I've ever had to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Richardson, TX
- Parts Used:
- 72017
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Scratches in Surface
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Holland, MI
- Parts Used:
- WP8172138
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken cooking tray
Just put it in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rae from Mogadore, OH
- Parts Used:
- WP8172138
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The glass tray broke while baking a potato.
Removed broken pieces. Ordered new glass tray. The tray came with excellent packing and double-boxed so there was no damage in transit. All I had to do was place the new glass tray onto supports in the oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from Sioux Falls, SD
- Parts Used:
- WP8172138
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
My glass cooking tray broke.
I was concerned I wouldn't get the correct glass plate, but it fit perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from PARADISE, PA
- Parts Used:
- WPR9800486
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
no heat
I looked up the #1 reason for no heat for my microwave on the site , and using my model number found that 92% of the time it was the Black Sleeve Diode. Ordered the $15 part, and installed it within 30 minutes. Most of the time was used for removing the built in microwave and removing the cover. Replaced the diode by finding it on the diagram that I printed from this site (free). Very relieved that we don't need to have our custom cabinetry re-sized to accommodate a new microwave. Thank you!
Was this instruction helpful to you?
Thank you for voting!