RH961G*H1 Hotpoint Microwave Oven Combo - Instructions

After supper, without biscuits, I removed the element by simply removing 4 screws with my nut driver. We went home and I immediately went online to your web site, inserted the old element part number, followed the ordering instructions, and in 3 dayd the new element had been delivered to our door. Several days later we were invited to mom's for dinner once again. I quickly installed the new element (perfect fit and works great) and enjoyed a great supper........with biscuits this time. Thank you.

Two 1/4" srews to remove the element from its mount, two 1/4" screws to remove wires and then the reverse to install new unit. Delivery was super fast and the price was half the price of the local dealers. I will certainly be a repeat customer.
Gary T.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, then i connect the new element and and replaced the screwes that held it in very simple and I must say Part select was very fast at getting me the correct part the first time , they have earned a spot in my Favorite list

Removed oven door by holding sides and pulling upward. It's easy to remove and replace. Removed shelves by sliding back and up, then out. Removed two hex nuts with socket wrench. They are on back wall of oven and secure element to that wall. I then pulled element out about 3 inches and disconnected the two leads.

I put new element in, reconnected two leads, replace two hex nuts and was done.

Turn off power to stove at circuit breaker before starting.

Couldn't be a much simpler repair. You pull the old element off by removing two screws. Then you slide the old element toward you several inches and remove the two screws holding the wires that are attached to the old element. To replace, just do everything in reverse. One cautionary measure, even though the oven is off, there is still a small amount of electricity going to the element. Turn the stove off at the circuit breaker, or unplug the stove before you attempt the repair.

The first thing I did wrong was order the wrong part. Then later I did find the Model number on the side of the bottom drawer. I reordered the right part and turned off the electrical breaker. Removed the old element. I then installed the element in the oven with 2 screw nuts and pulled out the stove, took off the back panel and slipped the wire nuts onto the element. Very simple. I am really thankful there is a place to order the part and it came the next day after I ordered it. WHOW!

Ordered part, took old bake element out, installed new bake element. It was real easy.

Flip the circuit breaker going to oven off, then used a 1/4 inch socket on the mounting flange bolts and the bolt head screws attaching the wires. Then used a flat head screwdriver to reattach the wires with the supplied screws and bolted the new element in place. Back to the circuit breaker flipped the switch and turned the oven on to test it, and now works fine. *be sure to remove the sticker before installation, use rubbing alcohol to remove any residue.*

took old element out , put new element in.very easy.

Removed 4 screw nuts and replaced with new baking element using same 4 screw nuts. Real easy job.

First I turned the power off to the oven/stove at the breaker box in the basement. Then I took the back plate off. Then I removed the two screws holding the wires onto the damaged element. Then I removed the two screws holding the element to the inside rear of the oven. Then I pulled the old element out and replaced it with the new element. I replaced the two screws that hold the element to the inside of the oven. Then I replaced the wires on the element where it protruded at the back of the oven. I put the back plate back on, slide the oven back in place and turned the power back on at the breaker and everything worked.

Shut off the power at the circuit breaker, removed the two nuts holding the element to the oven, unscrewed the two screws connected to the wire leads, removed the bad element and reversed the process to replace with the new one.

My husband first turned the main breaker off to the stove. Pulled the stove away from wall, took off the back plate, unhooked the element and out the new one in!!

Identify oven breaker and turn off power before starting. Opened oven door. Removed oven racks. Use 1/4" socket or nut driver to remove the 2 bolts holding heating element mounting bracket at rear base of oven. Carefully pull element out of installation mount to remove the 2 machine screws that attach electrical wires to the heating element. Reattach wires in same order as original element. Then reinstall new element in reverse order of removal. Took all of maybe 15 minutes! Excellent OEM Parts!

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.