JKP61G*J2 General Electric Microwave Oven Combo - Instructions

Removed two small bolt screws that held the bottom burner in place. Unscrew the two small screws that attach the oven wiring to the bottom burner. Put the bottom burner back in place and screw the two small bolt screws back in and its done.

so easy it doesn't need an explanation. Just remember to throw the breaker switch before beginning!

1) Turned off breaker and verified that the oven would not turn on. 2)Removed racks from the oven. 3) used nut driver to remove two mounting screws 4) used screwdriver to disconnect bake element from the wires. 5) used supplied screws to attach wires to new bake element. 6) pushed bake element into place and used nut driver to secure it in place with screws. 7) replaced racks 8) turned on breaker 9) tested by turning on oven with oven thermometer in place.

Flipped breaker to cut power to the oven.Loosened existing element using nutdriver to remove two screws in rear plate that attaches element to the rear wall of the oven.Pulled old element gently outward exposing two screws that attach element to existing wires.Removed those two screws with nutdriver to remove old element.Reversed the process. Turned power back on and turned on oven. Element worked perfectly.

I was able to find the part here and replaced it the same day. You could use smaller boxes and packing, but thanks you for the part and help.

Ordered the part and replaced the old one. Whole process took about 15 minutes.

I read the instrustions provided and proceded to remove the old Bake Element and installed the new Bake Element.
It was no problem at all and was just a simple job to replace the bad part.

Element went out on Wednesday; ordered part on Thursday; it arrived on Saturday (via regular service). Took out old part with hex screw drived, installed new and back in business.

1. isolate the main power supply. 2. remove backplate on old element,remove connecting terminals from old element; and withdraw from oven. 3. connect new element[make sure the connection is firm].replace backplate and secure with the two screws provided. switch on power, oven working perfectly.

A friend gave me your website. I looked up the model (is over 30 years old & obsolete!), but you listed a similar model. Part fit perfect, works great, heats to set temp quickly. Your do-it-yourself page was a big help...thanks! Replacement went quick and easy after I saw what needed to be done.

Looked up mfg. and part #,looked at blow up of stove on parts select, identified element. The part came overnite. Shut down power, removed 2 screws with a nut driver, pulled element foreward to reveal 2 screws attaching wires. Replaced in reverse order, turned on power, back in service. 10 minutes tops.

Unscrewed face plate, unscrewed electric wires hooked to element. Cleaned out oven while I was in there...nice and clean now. Installed new element same way I took it out. Easy as 'pie'..which we'll be baking again now that the oven works.

IT was fast and easy! Thanks

Turned the main breaker off and locked it out. Removed the original element using a 1/4" nut driver. Installed the new element using a Philips screwdriver. Turned the power on. Tha'ts it. Easy!

I turned off the power at the breaker for the oven. I had to use a small wrench to get off the two screws keeping the bake element in the oven.

I pulled it out a bit and exposed where the element screws into the power.

To prevent the wires from receding back into the wall after I unscrewed them, I taped them to the inside of the oven.

After removing the old element, I just installed the new one the same way. Screwed it into the power, and tightened the panel to the back of the oven.

Reset the breaker, and you're good to go.

Took 10 mins tops. It is pretty cramped in there and you need a good flashlight to see what you're doing.