JT965WF3WW General Electric Microwave Oven Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Frank from PARKER, CO
- Parts Used:
- WB44T10043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Lower Oven Broiler Stopped Working
Turned power off to oven
Unscrewed broiler nuts (total of 4)
Pulled Broiler out from back of stove
Disconnected wires
Reconnected wire
Remounted broiler and replaced bolts
Turned power back on
Unscrewed broiler nuts (total of 4)
Pulled Broiler out from back of stove
Disconnected wires
Reconnected wire
Remounted broiler and replaced bolts
Turned power back on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell from ARROYO GRANDE, CA
- Parts Used:
- WB44T10043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Remove and replace Broil (upper) heating element.
Turn off the power to the oven. (There should be a circuit breaker in the main power panel dedicated to just the oven) (the oven should be cool to the touch).
Open and remove the door by pulling it up and off the hinges (this is best accomplished with a helper).
Remove the racks (wire shelves).
Remove the two 1/4" mounting screws that secure the heating element to the back and the two screws that secure the element to the top of the oven..
Gently pull the wires out and disconnect them from the heating element.
Now reverse the process.
Connect the wires to the new heating element in the same fashion as they came off.
Push the wires and heating element back in place and secure with the four screws.
Replace the wire racks (shelves).
Replace the door (again, this is best accomplished with a helper).
Turn the power back on.
Run a test of the broiler to make sure the repair was completed properly.
voila!
Open and remove the door by pulling it up and off the hinges (this is best accomplished with a helper).
Remove the racks (wire shelves).
Remove the two 1/4" mounting screws that secure the heating element to the back and the two screws that secure the element to the top of the oven..
Gently pull the wires out and disconnect them from the heating element.
Now reverse the process.
Connect the wires to the new heating element in the same fashion as they came off.
Push the wires and heating element back in place and secure with the four screws.
Replace the wire racks (shelves).
Replace the door (again, this is best accomplished with a helper).
Turn the power back on.
Run a test of the broiler to make sure the repair was completed properly.
voila!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from FORT COLLINS, CO
- Parts Used:
- WB27X10928, WB24X829
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Microwave would run when door was opened, tripped breaker, wouldn't run at times, door opening and close would help/hurt operation
The breaker was tripped but fuse was ok on testing. I kept the fuse for possible future repairs. To access door switches and fuse on this model JVM1850CF001, remove 2 phillips screws at top. Then slide the grill to the left (toward hinges) about 1 cm and it should easily come off forwardly. Remove phillips screw underneath grill attaching the main panel. Lift the panel 1 cm and it will easily come off forwardly - I let it hang by the electrical cords. Now you can see/discharge capacitor(s). Remove 2 star screws inside door to loosen/remove/access door switch frame. 3 switches are held in the frame by plastic tabs - one tab per switch. One is primary and 2 are secondary door switches. I removed each switch one at a time by lifting tab, pulled off the electrical connector and filed the male metal connection on each switch. I replaced the switch with a loose button (loose and didn't click as crisply compared to the other switches) with a new secondary door switch. It was the lower secondary switch. Worked like a charm after that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kip from POWELL, OH
- Parts Used:
- WB27X10928
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Not heat
-unplug
-remove top and front covers
-unplug wire connectors from heating assembly
-remove heating assembly from metal stand and push out of the way
-remove metal stand from dry
-pull out heating assembly
-install new one in reserve order
-remove top and front covers
-unplug wire connectors from heating assembly
-remove heating assembly from metal stand and push out of the way
-remove metal stand from dry
-pull out heating assembly
-install new one in reserve order
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joan from SOUTHINGTON, CT
- Parts Used:
- WB25T10027
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Oven lamp globe shattered . Needed a replacement
The oven lamp shattered while cleaning. Easy to replace by hand.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from FAIRFIELD, OH
- Parts Used:
- WB20T10024
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Oven meat probe broken
This item worked as described. I paid more for this 'oem' probe than the generic 1 because i didn't want to chance it not working as others have reported.
- works great. tested it....snaps in, reads correctly, snaps out.
- works great. tested it....snaps in, reads correctly, snaps out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from MAYSVILLE, GA
- Parts Used:
- WB24X830
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave would run but not heat
Removed the control panel, one screw at the top. Removed 2 screws on the door switch holder and removed the door switch. VERY EASY.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Glencoe, NM
- Parts Used:
- WB23T10015
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Remove back panel or access sensor, replace sensor and panel
Removed back panel, change out sensor
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from SOUTHBURY, CT
- Parts Used:
- WB20T10024
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Temp probe was defective
Threw the old one out - plugged the new one in. Steak came out just as ordered - medium rare.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CHARLES B. from CLARKSVILLE, TN
- Parts Used:
- WB24X829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Smelling and smoking. Than stop.
I took the cabinet off and saw where the switch had been burnt. So I remove it and order another one from your company. And I put new clips on it with heat shrinks. We might get another 30 years out it, Although I'm 80 years old.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PHILIP from GEORGETOWN, TX
- Parts Used:
- WB06T10012
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broken turntable
replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WILLIAM from FRANKLIN, OH
- Parts Used:
- WB27T10566
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Oven Panel lights too dim to read and probe stopped working
1. Turn off breaker
2. Remove grill that around built in microwave; remove two top screws and to bottom (open oven door).
3. Remove two screws on the control panel.
4. Swing out and allow panel to suspend from its wire holder.
5. Trace the two harness cables from the old control board and disconnect from the counterparts inside the unit.
6. Remove the "ribbon" connector (do not damage, be gentle)
7. Remove the four screws holding the old control in place.
8. Place the new control board in place (do not connect the ribbon connector yet).
9. Plug in the harness to their respective receiving locations in the unit.
10. Install the "ribbon" connector into the new control panel.
11. Reverse steps 4-1 above ensuring all connections are solid and made correctly.
12. Turn on the circuit breaker and enjoy a "like new" oven!
2. Remove grill that around built in microwave; remove two top screws and to bottom (open oven door).
3. Remove two screws on the control panel.
4. Swing out and allow panel to suspend from its wire holder.
5. Trace the two harness cables from the old control board and disconnect from the counterparts inside the unit.
6. Remove the "ribbon" connector (do not damage, be gentle)
7. Remove the four screws holding the old control in place.
8. Place the new control board in place (do not connect the ribbon connector yet).
9. Plug in the harness to their respective receiving locations in the unit.
10. Install the "ribbon" connector into the new control panel.
11. Reverse steps 4-1 above ensuring all connections are solid and made correctly.
12. Turn on the circuit breaker and enjoy a "like new" oven!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheri from Sugar Land, TX
- Parts Used:
- WB06T10012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The roller guide broke where it fits over the turning mechanism.
removed the glass turning plate. removed the broken roller guide. replaced with the new one. I am very happy with not only the ease of fixing the problem, but how quickly I got the replacement part. I will use PartSelect again!!! And I will tell my friends.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from greensboro, NC
- Parts Used:
- WB06T10012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
microwave dish rotator hub broke
Very fast very easy. Part was exact match!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Shawnee, OK
- Parts Used:
- WB24X829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
time would count down but unit would not run & heat.
remove cover, unplug secondary door switch (top switch)
remove switch from holder, install new switch, plug in wires, replace cover, very easy. door switches are a common problem
with microwave ovens.
remove switch from holder, install new switch, plug in wires, replace cover, very easy. door switches are a common problem
with microwave ovens.
Was this instruction helpful to you?
Thank you for voting!