JTP86CF1CC General Electric Microwave Oven Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Anne Marie from Andover, MA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old dishwasher rack and silverware rack
The whole process was very easy! I just got the model number and bought a new rack and silverware holder on,one. There was no assembly needed so I just popped them in and replaced the old ones! Very easy to do!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda from Cave Creek, AZ
- Parts Used:
- WB41T10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
defective oven door seal
pull out defective seal with pliers clean area and press new seal into place making sure the spring clips on seal are completely inserted into door slots push ends of seal into holes in bottom of door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harriet from Jacksonville Beach, FL
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Open door. Put racks in.
nothing to it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Cranberry Twp, PA
- Parts Used:
- WB44T10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Heating element was fried.
Remove 2 nuts attaching element to oven. Pull element out 1" to 2" exposing electrical leads. Pull leads off old element. Replace with new. Toughest part is seeing the elements in a dark oven. Have a light handy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from Kernersville, NC
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
microwave won't heat
bought a fuse but that didn't solve the problem. Guess I need a new microwave
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Marcy, NY
- Parts Used:
- WB24T10065
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broken switch
This was a wall mounted oven. Turned off breaker. Pulled panel off by removing 6 screws. Pulled connectors off old switch. Removed old switch. Just a friction fit. I used my jack knife to get it moving. Pushed in the new switch and connected wires. (just push on tabs) Put panel back together and turned on breaker. Done, easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Green Valley, AZ
- Parts Used:
- WB24T10065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Door Switch
I unplugged the defective plug and replaced it with the new one. Took 5 min total
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BETTY from CYPRESS, TX
- Parts Used:
- WB48T10095
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
I needed an oven with three racks, mine came with two.
just slipped it in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- george from Moorpark, CA
- Parts Used:
- WB44T10018
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Wrench set
Oven heating element was burnt through.
Identified part with Part Select, placed order. Opened the power breaker for the oven. Removed oven door (slides off) to improve access, removed burnt element (2 screw and 2 electrical blade terminals). Installed the new element and tested. Reattached oven door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnette from Baltimore, MD
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no racks to oven
Easily glide in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from marstons mills, MA
- Parts Used:
- WB44T10018
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Lower heat element burned out
Very easy, only small issue was the holes for the two self taping screws were a bit high, so I had to drill two new holes to complete repair... Still a very simple repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bradley from Perryville, AR
- Parts Used:
- WB44T10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Heating Element
Removed two screws, removed two wires, installed new element. So easy a caveman could do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Orion from Vancouver, WA
- Parts Used:
- WB23T10015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven temperature was low when reading was correct
First of all, the sensor had the proper ohm reading...at ambient temperatures. I suspected the sensor because it would jump in large degree increments over 200°F. From what I read online, the only other part that would cause this was a faulty circuit board. I opted to try the $20 part first vs. the $200 part. It worked. One screw on the back top of the inside is all that holds the sensor in. Pull the wires out and you will find a quick-disconnect. New part had the same connector (thank you). Thread the wires back through the hole and replace the screw. Works like a champion (verified with an independent thermometer. That is all she wrote. I only wish I purchased two, since they don't last that long... 4 years...or so. I just bought the house built in 2007 and empty for a year... and it took 45 minutes to cook a pizza, and even then the bottom dough was light. A house without an oven is like a hot dog without mustard!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Niskayuna, NY
- Parts Used:
- WB06T10012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Turntable roller guide broken
Simply remove the broken turntable roller guide from the rotor and put in the new replacement -- less time than opening the box!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mohammad from Piscataway, NJ
- Parts Used:
- WB27X10928
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Powered Off completely
After reading reviews that there was no power what so ever and a fuse replacement will solve the problem, I tried it. Replacing the fuse is very easy (and I am not handy at all). All you have to do is remove the microwave cover from the top by removing two screws, slide the cover to the left and pulling the cover off. Then remove the grill in front of you, by removing one or two screws. The fuse is in front of you, use pliers and be firm but gentle. Replacing the fuse is easy but it did not solve my problem.
Was this instruction helpful to you?
Thank you for voting!