PT970DR1BB General Electric Microwave Oven Combo - Instructions

This door required a lot more screws to be removed in order to remove the inside window assembly. I counted a total of 19 screws. That is why the estimated time is 30-60 minutes.

- remove door from range following the basic guide to removing any range door.
- place door on work surface with the outside facing down.
- remove three 1/4 socket screws from bottom and two star screws on top.
- Flip door over, remove outer door panel and set aside.
- There will be a separate pane of glass that needs to be removed. Remove 1/4 socket screws holding glass and set aside.
- Slide door over your work surface edge so you can remove the star screws holding the door hinges (from underneath). You could flip the door over but the door would have to be flipped back once the hinges were removed.
- Remove the remaining 1/4 screws holding the aluminum shielding.
- Remove the shielding being careful not to disturb the insulation around the window.
- Remove the damaged window. Take note of the writing and orientation on the aluminum window frame. (upper right if hinges were on the bottom)
- Set the new window in its place.
- Reverse the process by replacing the aluminum shield, hinges, than internal glass pane.
- Set outer door on top and holding everything together, flip door.
- Tighten the two star screws on top and the three 1/4 socket screws on the bottom.
- Replace door. Don't forget to lift up those hinge tabs before trying to close the door.
All done. Pat yourself on the back for a job well done.

Per instructions on part select.com website. But needs further repair because still doesn't heat food and pad is partially disabled.

Disconnected the old socket ( 2 srews ) removed the two wires from the old socket, reconnected them to the new socket and reinstalled the lamp.

First and most important trun off curcit breaker. Use 1/4 inch but driver to remove socket (2) screws. Remove ground and hot wire clips from old socket, replace on new socket. Screw back into oven ceiling and turn on power. Reset clock and your are done. Very simple.

Very easy to remove the parts and to reassemble

This item worked as described. I paid more for this 'oem' probe than the generic 1 because i didn't want to chance it not working as others have reported.
- works great. tested it....snaps in, reads correctly, snaps out.

Ordered the part and pressed it on spindle.

Took the oven door off and removed the inner door panel, put new glass assembly part in and reassembled. The hard part was getting the door hinges locked back into place.

I have a double oven and coincidently I had to replace the two Oven Light Assemblies.
I am really glad about your web site because once I got the number from my oven model you guys were the first ones that came up. Thanks to your prompt and reliable service my oven is back to its original state.

Jose Figueroa

Purchased a new roller guide, simply dropped it in to place and the problem was solved. It took longer to open the box than it took to make the repair. Quick and easy.

Simply removed the cracked Guide Roller after finding that there was no way to repair the piece. Upon receipt of the part via FedEx it was a simple matter putting the new part in place. Things work fine.

twisted it in place

Remove the ice bin.
Turn the ice maker selection to "OFF"
Use small flat blade screwdriver to open the plastic ears on the electic plug in connectiion
Use #2 Phillips screwdriver to remove the screw on the front left side of the ice maker
Pull the ice maker forward until free of the two studs in the left side rear of the freezer wall
Check to see if the supplied water chute is the correct size for your application, if not remove the water chute from the old ice maker and place it on the new one.
Place the new ice maker in the freezer connecting the slots on the left read with the studs on the left wall
NOTE; IF THE ICE MAKER DOES NOT APPEAR TO BE LEVEL HORIZONTALLY REMOVE IT AND CAREFULLY REINSTALL IT TO ACHIEVE LEVEL
NOTE: ENSURE THE WATER DELIVERY TUBE RESTS IN THE RECEIVER TRAY
Reconnect the electrical plug ( needle nose pliers may be helpful in aligning the male plug with the female plug)
Move the selector from "OFF" to "ON"
Replace the ice bin and close the freezer door

Removed torx screws for door handle as well as torx screws for both hinges to separate the door halves to extract broken glass and to install new glass panel. Other reviews said not to remove hinge screws, however I had no problem reinstalling them.

First of all, there are FOUR panes of glass on the oven door and two different sizes. Make sure you're ordering the right pane. We initially got the wrong one and had to return/reorder.

Took door off hinges and set on table. Removed almost all screws. Two at the top are very long and almost spring loaded -- this was helpful when putting it back together.
When removing the layers, keep track of what/where screws are placed. Some are star-hole-head, some are hex-head (socket). Work slowly and carefully so as not to break additional panes of glass. Leave plenty of room in your workspace to set items aside while you get to the innermost part of the door.

For this part #, it's deep in the door layers and surrounded by fiberglass. Wear gloves so you're not itchy later. This part acts as a double-pane with a narrow aluminum frame around the two pieces of glass. Be careful not to bend the frame when removing the broken piece. One corner of the frame also has a hook-n-hole closure. Take care to not bend the hook too much.

We wiped all the glass pieces off to get all fingerprints, smudges, and baked-on foods removed. Then we put the pieces/parts back -- a lot like a puzzle. Had the oven back up and running with no problems. It may take two people to get the door back on the hinges just because of the weight and awkward position they need to clamp back together.