JKP62G*K3 General Electric Microwave Oven Combo - Instructions

I was so relieved to find the replacement glass for the door on my built in microwave/oven. I was worried about shipping this tempered glass panel but it was recieved well packaged. As soon as I openned the packing, I removed 6 scews holding the trim around the oven door, slide in the new glass, reinstalled the scews and grabbed the glass cleaner. I was finished. Part select is a tremendous resource.

Two 1/4 inch screws and then two Phillips head screws that was it

Removed old new one fit perfectly

1) Turn off power at circuit breaker panel
2) Slide out Range from wall
3) Unplug Range
4) Remove back panel and unplug electrical connections to socket
5) From front of oven, remove glass cover over old oven light bulb and remove flange that holds socket and bulb
6) Remove old socket from mounting flange and discard.
7) Place new socket into mounting flange
8) Screw mounting flange and new socket into the oven from front. Reattach electrical connections from back.
9) Screw in new light bulb from front
10) Replace existing glass cover over new light bulb and snap wire holder in place
11) Replace back panel
11) Plug in range
12) Slide range back to original position
13) Turn on power
Works like a charm! Thanks for having the parts after 30 years!

Turned off the power to the stove, pulled out the racks, unscrewed the old element and pulled off the electric connectors...easy so far...installed the new element to the electric connection, pushed back into the back of the stove and reinstalled the screws. Turned on the power and then the stove...now I can bake an apple pie!

Ordered Bake Element - 240V from Partselect , when part received removed broken element with a screwdriver., replaced with new Bake Element with a screwdriver. Very easy to do.

replaced lights in refrigirator and freezer

removed parts from carton,,shut off breaker to over,,cradled the flash light,removed cover plate,,removed element,,removed screws from wires,,reversed to install,,screwed wires to element,,placed element in place and installed plate nuts,,,turned breaker back on...

As instructed in your directions

First removed oven door, according to Reader's Digest repair manual, then removed two screws holding element. Pulled element out several inches, then removed one side of bracket holding up front of element so that bad element could be pulled further out. Then disconnected two red wires from one side and two light blue wires from other side. Removed old Element. Attached two light blue wires to one side and two red wires to other pole, inserted element back into rear wall and attached with two screws, Re-attached bracket holding up front of element. Re-installed door. Tested and it worked fine.

Broiler element arrived at my door 3 days after ordering which was nice. Apparently the billing dept. is out of the USA so don't be surprised, like I was, to find a suspicious looking charge for a currency exchange fee (mine was 42 cents). I had to drill two new screw holes in the base of the new element in order for it to fit my oven. I also had to use heavy wire snips to cut off about an inch of the top of the new element base. The female electrical connections also had to be spread out with needle nose pliers since the new element connections were slightly thicker. With all of the issues I had I was frustrated and it took about two hours. On the other hand, the part works perfectly and was priced right. Hopefully it will fit perfectly out of the box for your oven.

I removed the unit easily with anut driver, however the unit also supported the thermo-link. I had to use the hack saw to relieve a small opening for the thermo-link to pass through. No real problem. Then a few holes to be drilled to attach the 'link' to the base of the broiler unit.

BUT-I went into the website listed on the box. GEAppliances.com Guess what? Their price was twice yours!!

Removed the old part by removing inside frame. Used a screwdriver to gently wedge it out, then had access to the screws holding it to the metal frame. The part needed (door trim) was white, but no longer available. I ordered the part in black color. The original part had faded from white to a cream. I took the broken part to Home Depot and they made up a paint that matched the faded color. I painted the part with a foam brush. Diluted the paint to avoid runs and painted several times. It went back together fairly well except make sure you use double back tape to hold glass assembly in place. It would be better if two people do this job. one holding the glass and frame while the other is attaching the door trim from the other side. The door trim has some snap in parts that go into the metal frame along the hing side, make sure that they snap in so that the door trim dose not touch the main cabinet when opening and closing the door.

Once I saw the gasket that was supplied it was really easy to see how to install it.
A hook on either end of the gasket gave me the clue on how to remove the old one.
Off with the old and on with the new in less than 2 minutes!!
Extremely easy!! Thanks Part Select for having what I needed!

I looked on Youtube for a how to video. It was accurate but the screws in my oven were NOT phillips head screws, they turned out to be sheet metal screws. I used pliers at first which was a PAIN but then I borrowed a socket wrench from the neighbor that was MUCH better!! I had wanted to do it myself to prove to my husband and son that I could but I ended up needing their help because the screws were so tight.... But we did the repair ourselves!!!