JHP97G*Y2 General Electric Microwave Oven Combo - Instructions

First I turned off the power to the stove,removed oven racks,removed the two screws that held the element in place,pulled unit out a couple inches ,removed the two screws that held the wires in place ,removed element.
Placed new unit where old one went and placed wires in proper order and put together and placed back . turned power back on and WALAA......nothing......apparently that wasnt the problem....Husband baught me a new stove,after 35 years why not.

The only hard part of the job is removing the old, corroded terminal block. Be careful not to break the electrical wire. Other than that, just sand the contacts and reassemble. This is the second one I have replace on my 4 burner stove. 2 more to go.

.....then tested for voltage, had it. Ordered the element through partselect.com and it came in the mail THE NEXT DAY! No kidding! Installed it and the wife is back to her good cooking. All is well, thanks partselect.com. John R., Pompano Beach, Florida

removed the old, replace the new. The delivery of my new part was exceptional, received the very next day after ordering.

Simple replacement. Price for replacement was excellent. Cheaper than any replacement I priced locally and arrived the day after I ordered.


Thanks!

My sons helped with that. They had to use a pliers to remove the old screws (did not have to notches). After that they they removed the element. Then the wires had to be disconnected (after we unplug the oven from the main power source. Then the wires were connected to the new heating unit. We only got one screw in so far will work on getting the second one in when they return tomorrow. I did turn on the oven and it works!!!

Thank you to the nice young man that helped me on the phone.

Removed the two screws which held the element in place. Then I pulled the element out about 2-3 inches and disconnected the two wires. Of course I turned off the breaker which fed the range. This had been done earlier so that wife could throughly clean the oven while the element was out of the way, When the new element arrived, we put it into the oven, reconnected the wires to the lugs on the element, pushed it back into the hole, pushed the insulation which protruded back into the hole, and replaced the two screws which held the back plate in place. Turned the breaker back on and turned oven on to test the repair job. Everything worked AOK.

Ordered the part online, received it in a coupledays and my son-in-law installed it in a flash. The cost was very reasonable also. The whole experience was a snap. Thanks so much!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, and reconnected the two wires back with the new screws. Reinstalled the element by reassemblyinig the two screws holding it in place.

This job was easy. I removed two screws to release the element from the back of the oven, two more screws to release the electrical connection, connected the new element with the new screws provided and reattaced the heating element to the back of the over. It took two tries to get the element so that is sat level at the bottom of the oven. Ten minutes later, I was making dinner!

Unplugged oven, removed 2 screws that hold the element in place. Pulled element to expose wires. Disconnected wires & removed old element. Reversed removal for installation, plugged in and worked great.

I made sure the power was off. I removed two screws from the mounting plate, then I pulled the heating element forward two inches. Where the wires were attached by two screws, I removed those screws also; the heating element was freed up. I then removed it and replaced the 28 year old heating element with a brand new one.

I removed the old element after turning off the breaker to the oven. Remove the two screws that hold it to the back wall of the oven, slid it towards me exposing the wire connection. Removed the screws from the wires and removed the old element. Cleaned the oven and installed the new element by reversing the steps I just talked about. Quick and easy, oven has never worked better.

Unscrewed the two screws that held it in place; disconnected the old; connected the new; replaced the screws. DONE.

First I removed the 2 screws holding the element in place then pulled the element out a few inches.
I removed the 2 screws that connected the wires to the element and removed old element from oven. The new element was placed in the oven and connected by reversing the steps just described. New element works perfectly!