JKP61G*01 General Electric Microwave Oven Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from JONESBORO, AR
- Parts Used:
- WB44X200
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Burnt into
Two 1/4 inch screws and then two Phillips head screws that was it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary C from KISSIMMEE, FL
- Parts Used:
- WB44X200
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Baking element broken
Turned off the power to the stove, pulled out the racks, unscrewed the old element and pulled off the electric connectors...easy so far...installed the new element to the electric connection, pushed back into the back of the stove and reinstalled the screws. Turned on the power and then the stove...now I can bake an apple pie!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from WINTERVILLE, GA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lights blown out
replaced lights in refrigirator and freezer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from DANVILLE, KY
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Heating element severed
Removed old new one fit perfectly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from CLAYMONT, DE
- Parts Used:
- WB44X200
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
second time repaired in about ten years
removed parts from carton,,shut off breaker to over,,cradled the flash light,removed cover plate,,removed element,,removed screws from wires,,reversed to install,,screwed wires to element,,placed element in place and installed plate nuts,,,turned breaker back on...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Lafayette, CO
- Parts Used:
- WB44X173
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
broiler element circuit broke
First removed oven door, according to Reader's Digest repair manual, then removed two screws holding element. Pulled element out several inches, then removed one side of bracket holding up front of element so that bad element could be pulled further out. Then disconnected two red wires from one side and two light blue wires from other side. Removed old Element. Attached two light blue wires to one side and two red wires to other pole, inserted element back into rear wall and attached with two screws, Re-attached bracket holding up front of element. Re-installed door. Tested and it worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Fort Worth, TX
- Parts Used:
- WB44X173
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Broiler element stopped heating
Broiler element arrived at my door 3 days after ordering which was nice. Apparently the billing dept. is out of the USA so don't be surprised, like I was, to find a suspicious looking charge for a currency exchange fee (mine was 42 cents). I had to drill two new screw holes in the base of the new element in order for it to fit my oven. I also had to use heavy wire snips to cut off about an inch of the top of the new element base. The female electrical connections also had to be spread out with needle nose pliers since the new element connections were slightly thicker. With all of the issues I had I was frustrated and it took about two hours. On the other hand, the part works perfectly and was priced right. Hopefully it will fit perfectly out of the box for your oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from Charlotte, NC
- Parts Used:
- WB44X173
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Broiler unit burned out
I removed the unit easily with anut driver, however the unit also supported the thermo-link. I had to use the hack saw to relieve a small opening for the thermo-link to pass through. No real problem. Then a few holes to be drilled to attach the 'link' to the base of the broiler unit.
BUT-I went into the website listed on the box. GEAppliances.com Guess what? Their price was twice yours!!
BUT-I went into the website listed on the box. GEAppliances.com Guess what? Their price was twice yours!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from Cupertino, CA
- Parts Used:
- WB2X3422
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Gasket Tear - Needed Replacing
Once I saw the gasket that was supplied it was really easy to see how to install it.
A hook on either end of the gasket gave me the clue on how to remove the old one.
Off with the old and on with the new in less than 2 minutes!!
Extremely easy!! Thanks Part Select for having what I needed!
A hook on either end of the gasket gave me the clue on how to remove the old one.
Off with the old and on with the new in less than 2 minutes!!
Extremely easy!! Thanks Part Select for having what I needed!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from LORDSBURG, NM
- Parts Used:
- WB1X500D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
No Spin Cycle
Lid Switch.
Rewiring connection.
Function is satisfactory.
Fan belt ordered is saved.
A 1970 Clothes Washer.
Rewiring connection.
Function is satisfactory.
Fan belt ordered is saved.
A 1970 Clothes Washer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from SAN JOSE, CA
- Parts Used:
- WB27X7
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
CERAMIC FUSE BLEW WHILE HEATING VEGETABLES
I found an exploded view diagram of of my microwave model which was very helpful. You need only remove outside metal skin by removing 4 screws on either side and 4 more on the back. Remove 4 plastic hole plugs from the top mounting inserts. Gently pull sides out and lift up and back to remove outer skin. The fuse is located on the back right corner behind the control panel. You access from the side. The fuse is under the spreader bar. Lift fuse up gently to remove.
P.S. It was the MSP Capaciter and or the interlock switch, snap apart 21A (19) failure that actually caused the ceramic fuse to blow.
P.S. It was the MSP Capaciter and or the interlock switch, snap apart 21A (19) failure that actually caused the ceramic fuse to blow.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RONALD from MT PROSPECT, IL
- Parts Used:
- WB44X200
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
BURNT-OUT ELECTRIC BAKE OVEN ELEMENT
USE A MAGNETIZED SCREW DRIVER. BE CAREFUL THE OVEN ELECTRIC WIRES DO NOT FALL BACK INSIDE OF THE OVEN. HAVE LONG NOSE PLIERS HANDY. MAKE SURE YOU TILT THE ELEMENT SO THAT THE ELEMENT TERMINALS ALIGN PROPERLY WITH THE THE SCREWS AND ELECTRIC WIRES. THAT'S IMPORTANT ELSE YOU CANNOT GET THE SCREWS STARTED TO ATTACH THE ELEMENT.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from SPARTANBURG, SC
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Burnt bake element
Removed door. Take out two hold down screws for element. Hold electrical tab with pliers and remove screw on each tab. Reverse directions to reinstall. Door may have screws to remove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- wayne from GARLAND, TX
- Parts Used:
- WB44X173
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
broil element burn into
turn off electricity to stove and simply remove the screws from the heating element and put new element back in place .put screws in and turn power back on and test.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from TABERNACLE, NJ
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Burnt out element
As instructed in your directions
Was this instruction helpful to you?
Thank you for voting!