JKP78G*K3 General Electric Microwave Oven Combo - Instructions

removed old element and installed new, and oven is up and working like new

Took out old element with screw driver and replaced new element with screw driver, very simple.
We were so happy with the customer service, had the new element the very next morning. Thank you.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires..Took out the old element and reversed tjhe procedure to install the new one

replaced with a new part . Thanks for all your assistance in getting the correct part

remove two screws from back of oven holding element to back of oven. Pull out gently, remove two screws holding wire connections(power wires) throw away old element. Place new element into oven. Reconnect element to power wires using screws. Push element back into back of oven. Replace screws holding element in place. Turn oven on to check for proper connections.

The part was ordered on a Friday afternoon. It arrived the next morning! Threw the breaker, removed the racks, removed the old element and put in the new one. Done.

Bottom bake element is fastened to back wall by 2 screws remove those first.
Slowly pull out old bake element notice 2 wires are fasten to old bake element by 2 philips head screws. Remove screws from wires fastened to old bake element
Discard old bake element.

Reverse the order for assembly.
Replacement part is the exact fit and entire replacement took 15 minutes.

EASY REPLACEMENT

Unscrewed the two screws holding the element to the back oven wall, then I was able to pull the element out. I then unsrewed the two screws holding the two wires to the element. Installation was the reverse. Pretty simple job.

Part was a breeze to install. I turned the power off to the oven at the breaker. I then unscrewed the bolts holding the old element in and disconnected the wires. I attached the wires to the new element and bolted it back onto the oven. I turned the breaker back on an tested the new bake element. Worked great! Now it heats up like it should. The whole process was very easy.

I removed the two screws that keep the element in place.Then I pull the element a little bit and disconnected the two wires and removed the old element. Then I reconnected the two wires on the new element then put the element back on position and put back the two screws that keep the element in place. Done.

removed 4 screws and exchanged units put the 4 screws back in. about 10 min.

Turned the main breaker off and locked it out. Removed the original element using a 1/4" nut driver. Installed the new element using a Philips screwdriver. Turned the power on. Tha'ts it. Easy!

I turned off the power at the breaker for the oven. I had to use a small wrench to get off the two screws keeping the bake element in the oven.

I pulled it out a bit and exposed where the element screws into the power.

To prevent the wires from receding back into the wall after I unscrewed them, I taped them to the inside of the oven.

After removing the old element, I just installed the new one the same way. Screwed it into the power, and tightened the panel to the back of the oven.

Reset the breaker, and you're good to go.

Took 10 mins tops. It is pretty cramped in there and you need a good flashlight to see what you're doing.

so easy it doesn't need an explanation. Just remember to throw the breaker switch before beginning!

1) Turned off breaker and verified that the oven would not turn on. 2)Removed racks from the oven. 3) used nut driver to remove two mounting screws 4) used screwdriver to disconnect bake element from the wires. 5) used supplied screws to attach wires to new bake element. 6) pushed bake element into place and used nut driver to secure it in place with screws. 7) replaced racks 8) turned on breaker 9) tested by turning on oven with oven thermometer in place.