JKP65G*03 General Electric Microwave Oven Combo - Instructions

First turned power off for oven circuit at the breaker box then removed two screws that hold element in place. Pulled element out, tested for current, then removed two screws holding wires to element. Took old element from oven and inserted new element. Reattached wires with screws provided, and pushed element into opening. Replaced two screws securing element to back wall of oven. Turned the circuit breaker back on then checked to ensure the oven was working.

1. Turned the electricity off at the fuse box.
2. Took out the two metal screws holding the element to the oven back.
3. Unscrewed the screws holding the element coil, pulled the element out some and disconnected the two wires.
4. Replaced the old element with the new one.

Removed the 2 screws that held element in place. Pulled the element out about 2 inches to disconect the wires. I then reattached the new element and replaced the screws holding the element in place.

First I turned the power off to the oven. Then I tried to take out the nuts holding in the element. One nut came off easily, the other one was rusted on, I had to use wd40 to loosen it. The project was easy once I got that nut off. I pulled out the element, which is connected to two wires. I took those screws out, connected the new element to the wires, re-attached the screws, pushed it back in, attached the nuts that hold the element in the oven. Then I turned the power back on and the oven works like a charm. I installed it the day I got it. I was surprised how quickly it was shipped to my house. I am so glad I repaired the oven, a new one would have cost over $800, I bought the element for less than $30, including shipping! It also sets a good example for my daughter. It taught her that her mom can repair things too, it's not just something men can do!

Removed the broken one by disconnecting the two screws , yellow and red wires and replacing it with the new part you sent me. Very simple.

Removed the bad part. There were 4 screws,
Found part on the internet.
When part arrived I installed it using the screws that I removed when I took out the bad part.

I have to admit that I tried to remove the element myself but I did not have the right tool for the last two screws. If I did it would have been very easy. I ordered the part and had someone else put it in so I cheated.

First of all let me say, I am grateful you are supplying parts to an oven made in 1984. I noticed the crack the day before Thanksgiving and immediately started looking for the part because Thanksgiving was the least of my worries. I have a countertop broiler to cook the turkey and dressing in but I am catering a huge party in a week and really need the oven in top shape. Due to minor surgery I have not made the repair but I want to say thank you for getting the part to me on Saturday right after Thanksgiving. Wednesday to Saturday with a two day holiday is incredible. Thanks for the great customer service.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires on the element. Put in the new element and reconnected the wires. Pushed the wires and element back into place and screwed in the screws that hold the element in place.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and replaced the two wires that hold the element in place. I received the part within about 36 hours after placing order.

Turned off power. Unscrewed two screws and pulled old element out of oven. Disconnected the two wires. Cleaned oven thoroughly, held new bake element with soft rag so as to not get fingerprints all over it. Wired new element and screwed it back into oven.

Baking sweet potatoes as I write, they will be delicious with my black-eyed peas and ham, a New Year's tradition in my neck of the woods.

First turned off the power to the oven then removed two screws holding element in place. Pulled it out a couple inches disconnected the two wires. Then connected two wires to the new element pushed it back into two place and reinstalled screws that hold element in place. Really easy about 15-20 minutes to complete

Easy repair. The toughest part was disconnecting the wiring from the old element. Once that was disconnected it went very well.

Took out the old and put in the new! Easy and inexpensive repair (especially because my husband did it!)

On Thanksgiving Day, we were making a pecan pie. The lower oven started to smoke and flame. We quickly turned off the oven, removed the pie, and noticed that half of the lower burner element had turned into cinders. I copied down the part number and serial number of the oven, went to Google, and found the replacement part that I needed. Once the oven had cooled down, I turned off the circuit braker for the oven and tried to remove the burned out heating element. The good news was that I could remove it with my SAE socket set. I then ordered the part on line, knowing with confidence that I could do the replacement myself.
The part arrived one day after I got the email that the part had shipped. That is great service!
I waited till the next day to do the repair since I needed to have the right tools lined up and I needed to wear clothes that might get dirty when working deep inside the oven. A flashlight and a socket set with a 1/4 inch drive were the main tools I needed to do the electrical connections and the oven connection. I also used a blunt putty knife to clean out some of the goo in the oven.
After the repair, I turned the circuit breaker back on and placed a separate oven thermometer into the oven for the first test. The oven worked just fine at 250, 350, and 450 degree settings. Wife is now happy!