JT965BF3BB General Electric Microwave Oven Combo - Instructions

Turn off the power to the oven. (There should be a circuit breaker in the main power panel dedicated to just the oven) (the oven should be cool to the touch).
Open and remove the door by pulling it up and off the hinges (this is best accomplished with a helper).
Remove the racks (wire shelves).
Remove the two 1/4" mounting screws that secure the heating element to the back and the two screws that secure the element to the top of the oven..
Gently pull the wires out and disconnect them from the heating element.
Now reverse the process.
Connect the wires to the new heating element in the same fashion as they came off.
Push the wires and heating element back in place and secure with the four screws.
Replace the wire racks (shelves).
Replace the door (again, this is best accomplished with a helper).
Turn the power back on.
Run a test of the broiler to make sure the repair was completed properly.
voila!

Turned power off to oven
Unscrewed broiler nuts (total of 4)
Pulled Broiler out from back of stove
Disconnected wires
Reconnected wire
Remounted broiler and replaced bolts
Turned power back on

1. Turn off breaker
2. Remove grill that around built in microwave; remove two top screws and to bottom (open oven door).
3. Remove two screws on the control panel.
4. Swing out and allow panel to suspend from its wire holder.
5. Trace the two harness cables from the old control board and disconnect from the counterparts inside the unit.
6. Remove the "ribbon" connector (do not damage, be gentle)
7. Remove the four screws holding the old control in place.
8. Place the new control board in place (do not connect the ribbon connector yet).
9. Plug in the harness to their respective receiving locations in the unit.
10. Install the "ribbon" connector into the new control panel.
11. Reverse steps 4-1 above ensuring all connections are solid and made correctly.
12. Turn on the circuit breaker and enjoy a "like new" oven!

Before you get started on this be sure that you already have the Bottom Cabinet Trim Assembly (item #PS952490) either ordered or installed. We were not aware that you had to order both trim items separately which meant we had to remove the oven door twice. Using the screwdriver to pull back the door tabs, we first removed the oven door. The trim installed very easy. We just lined up the holes, pushed in, and then down on the trim to lock it in place. When reinstalling the oven door, be sure that door latches are almost fully extended before reinserting them into their slots.

Turn the glass enclosure counterclockwise to expose bulb.Turn the power off at circuit breaker panel.Handle the bulb carefully with paper towel covering the bulb.Push the bulb in socket.replace glass enclosure,turn power back on.

Very fast very easy. Part was exact match!

removed the glass turning plate. removed the broken roller guide. replaced with the new one. I am very happy with not only the ease of fixing the problem, but how quickly I got the replacement part. I will use PartSelect again!!! And I will tell my friends.

Replaced it

Replaced the fuse. Result; did not fix the problem.

Replace the fuses

I think I could have managed with just the diode but since I had to pull it I decided to replace all related parts per my research. The Magnetron more than likely was fine.

The actual repair was relatively easy but access to the area in the oven made it a little difficult. Just unscrew 5 screws with a nut driver, unplug the old element, plug in the new element and reinstall the 5 screws. The only thing that made this repair difficult was being able to reach the connectors where you plug in the new element. They are loose wire connectors that don't reach very far out of the element receptacle. It was difficult to hold the end of the connector and plug in the new element because the oven door is in your way. Maybe it is easier if you take the oven door off first?

First unplugged the microwave, took top grill off, took control panel off, took wires off and used color coded tape to make sure they went back in right places, took fuse out and replaced it and put every thing back and it all worked fine and to top it off my wife did it all. So it was pretty easy.

Turned off power to range, slid range out from counter, removed convection fan cover, removed convection fan blade, removed back of range panel over convection motor, removed motor, put in new motor, put range panel back on, put new fan blade on front of motor, replaced fan cover, turned power on. No more clunking noise from motor.

I shut off power to the microwave, discharged the Hi-voltage capaciator and disconnected the wires to it, then removed the screw and bracket that held the capaciator in place. After removing and replacing the capaciator, reattaching wires and mounting bracket, and replacing the 15amp fuse, the microwave woked fine.