Models > JTP28BF1BB > Instructions

JTP28BF1BB General Electric Microwave Oven Combo - Instructions

Jump to:

All Instructions for the JTP28BF1BB
61 - 75 of 103
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Frank from PARKER, CO
Parts Used:
WB44T10043
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers
Lower Oven Broiler Stopped Working
Turned power off to oven
Unscrewed broiler nuts (total of 4)
Pulled Broiler out from back of stove
Disconnected wires
Reconnected wire
Remounted broiler and replaced bolts
Turned power back on
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Russell from ARROYO GRANDE, CA
Parts Used:
WB44T10043
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Remove and replace Broil (upper) heating element.
Turn off the power to the oven. (There should be a circuit breaker in the main power panel dedicated to just the oven) (the oven should be cool to the touch).
Open and remove the door by pulling it up and off the hinges (this is best accomplished with a helper).
Remove the racks (wire shelves).
Remove the two 1/4" mounting screws that secure the heating element to the back and the two screws that secure the element to the top of the oven..
Gently pull the wires out and disconnect them from the heating element.
Now reverse the process.
Connect the wires to the new heating element in the same fashion as they came off.
Push the wires and heating element back in place and secure with the four screws.
Replace the wire racks (shelves).
Replace the door (again, this is best accomplished with a helper).
Turn the power back on.
Run a test of the broiler to make sure the repair was completed properly.
voila!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from HIGHLAND, UT
Parts Used:
WB44T10018
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Oven not heating
Removed element. Ordered new one. Installed it.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sherry from SAINT PAUL, MN
Parts Used:
WB56T10105
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
Replaced cracked inner oven door glass
This went pretty smoothly. Watch the video and just follow along step-by-step and it goes well. It would have only taken about 30-45 minutes (even being careful and slow) but I ended up placing the glass twice (be very careful and triple check that all the insulation gets poked under the housing and none is sticking out). The first time I had a small piece sticking out. (Use gloves for this part so your hands don't itch). The second time I needed to redo part of it is I forgot one of the spacers on the door handle and had to get that in there so the handle worked properly. I also took the time to clean the oven while the door was off so that took some time. Total I probably had 1.5-2 hours into this project but at least half of that was me cleaning and being fussy. This is an easy repair. I'm not a confident repair person and this wasn't difficult. It was a little time consuming but well worth the cost vs calling a repair person or buying a new appliance. You do need to have a specialty star head on a screwdriver but my simple tool kit had all the tools I needed. The oven has been working great since the repair.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Clemmie from Alpharetta, GA
Parts Used:
WB20T10003
Difficulty Level:
Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Screw drivers, Socket set
Lower oven of double oven would not turn off. It stayed over 130F
Disconnect power at the breaker panel. Verify that it is off. Remove the upper and lower oven doors. Remove the screws that hold the oven in the cabinet. Remove the controls panel at the top. Disconnect the power cord inside the controls cabinet. Pull the ovens from the wall and place on the floor. Remove the covers on the back of the oven. Pull the old probe from the lower oven. For the new thermostat, remove one wire at a time and add it to the new thermostat. When all wires have been moved to the new thermostat run the new probe down the back of the oven and install where you removed the old probe.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rachel from Maryland Heights, MO
Parts Used:
WB44T10018
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
lower bake element went out
basically unscrew two screws, unplug, plug new one in and screw the screws back in.
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Louis from LEAGUE CITY, TX
Parts Used:
40A15
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Change bulb
Easy
3 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jennifer from Castaic, CA
Parts Used:
WB07T10401
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Needed to replace missing trim
Before you get started on this be sure that you already have the Bottom Cabinet Trim Assembly (item #PS952490) either ordered or installed. We were not aware that you had to order both trim items separately which meant we had to remove the oven door twice. Using the screwdriver to pull back the door tabs, we first removed the oven door. The trim installed very easy. We just lined up the holes, pushed in, and then down on the trim to lock it in place. When reinstalling the oven door, be sure that door latches are almost fully extended before reinserting them into their slots.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Scott from Troy, MO
Parts Used:
WB44T10018
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
While on self clean, the bake element began to burn
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I plugged in the new element and proceeded to clean the oven which is what I was doing when the problem occured.
2 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Roscoe G from ROCHESTER, NY
Parts Used:
40A15
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
2 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Orion from Vancouver, WA
Parts Used:
WB23T10015
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Oven temperature was low when reading was correct
First of all, the sensor had the proper ohm reading...at ambient temperatures. I suspected the sensor because it would jump in large degree increments over 200°F. From what I read online, the only other part that would cause this was a faulty circuit board. I opted to try the $20 part first vs. the $200 part. It worked. One screw on the back top of the inside is all that holds the sensor in. Pull the wires out and you will find a quick-disconnect. New part had the same connector (thank you). Thread the wires back through the hole and replace the screw. Works like a champion (verified with an independent thermometer. That is all she wrote. I only wish I purchased two, since they don't last that long... 4 years...or so. I just bought the house built in 2007 and empty for a year... and it took 45 minutes to cook a pizza, and even then the bottom dough was light. A house without an oven is like a hot dog without mustard!
Was this instruction helpful to you?
Thank you for voting!
Customer:
michael from marstons mills, MA
Parts Used:
WB44T10018
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Lower heat element burned out
Very easy, only small issue was the holes for the two self taping screws were a bit high, so I had to drill two new holes to complete repair... Still a very simple repair.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Peter from Green Valley, AZ
Parts Used:
WB24T10065
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Broken Door Switch
I unplugged the defective plug and replaced it with the new one. Took 5 min total
Was this instruction helpful to you?
Thank you for voting!
Customer:
Vicki from Irvine, CA
Parts Used:
WB48T10095
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Replaced damaged oven rack
I ordered the oven rack on a Tuesday and received it the very next day - was wowed at the service.
Was this instruction helpful to you?
Thank you for voting!
Customer:
BETTY from CYPRESS, TX
Parts Used:
WB48T10095
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
I needed an oven with three racks, mine came with two.
just slipped it in
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JTP28BF1BB
61 - 75 of 103