JBV42G*H2 General Electric Microwave Oven Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from VINELAND, NJ
- Parts Used:
- WB21X36771
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Electric Burner Control Broken
New one a little different ,but it was marked for wiring!
Had to install upside down because wires would not reach right side up!
Had to pull back side of knob out and turn 180 degrees and glue in knob, so knob would be right side up!
Works fine! Now all burners work again!
Had to install upside down because wires would not reach right side up!
Had to pull back side of knob out and turn 180 degrees and glue in knob, so knob would be right side up!
Works fine! Now all burners work again!
Was this instruction helpful to you?
Thank you for voting!
Surface Burners were very slow.
Removed old surface burners and replaced them by plugging in the new surface burners. Now they work GREAT! Parts ordered and received with-in 3 business days. Fed EX delivered parts in good order very quickly. We recommend PartSelect.com
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bernard from N CHARLESTON, SC
- Parts Used:
- WB17X5095
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no burnt wire
Replace part an wires
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Southern Pines, NC
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Surface element was corroded.
Removed existing surface element and replaced with new element.
P.S.
Part Select service was excellent.
P.S.
Part Select service was excellent.
Was this instruction helpful to you?
Thank you for voting!
Small elements were losing heating power and large elements did not work.
I unplugged each element from the terminal it was plugged into and then plugged the new element in. I also replace the drip pans and trim rings while I was at it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doris from Redwood City, CA
- Parts Used:
- WB3X459
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
timer knobs missing
Just pushed the new timer knobs onto the stem. They fit and now I can set the oven timer without having to use a pair of pliers to grip the stem and turn it.
Two of the knobs fit perfectly.
The stem for the the clock was broken off and there was not enough of the stem left for the new knob to fit.
Two of the knobs fit perfectly.
The stem for the the clock was broken off and there was not enough of the stem left for the new knob to fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carole from Cleveland, OH
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
melted electric range element
Because of the superb pics and descriptions on the Part Select site, I was able (with NO range model number) to order the correct range element for beloved son's stove. He plugged it in in 3 seconds, works great !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Emma from The VIllags, FL
- Parts Used:
- WB30M1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old unit failing to heat all coils
I first removed the unit by pulling gently from connection. Replaced the new one in that same manner - simply inserting into connection.
Very easy, I'll probably try it again soon.
Very easy, I'll probably try it again soon.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from WINTERVILLE, GA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lights blown out
replaced lights in refrigirator and freezer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAMES from SAN JOSE, CA
- Parts Used:
- WB17X5113
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
terminal block not working
simple remove the old one, strip old wires to make longer, twist wires together, put on wire nuts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Hindman, KY
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Burner wouldn't operate
Took Switch panel off range. Disconnected Infinite switch. Reinstalled infinite switch.. Replaced panel. Repair was very simple and self explainatory.
Knott County Housing Authority Maintenance Personnel
Knott County Housing Authority Maintenance Personnel
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Catherine from silver spring, MD
- Parts Used:
- WB17X5113
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
needed to replace a receptacle
I had already removed the worn out part. The new part came with wire joint covers and connecting them was fine. The brace that came with the part did not actually fit onto the stove burner well; so I cleaned and used the older brace - but, when I went to put it back in place, the bearings on the original self locking bolt were stripped. So, I had to find a replacement bolt with a nut. Found that I had some of those on hand. Once the brace was firmly in place, the rest was easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from Dallas, TX
- Parts Used:
- WB17X5113
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The heating coil on the stove blew, or wouldn't work.
I simply replaced the female part of the plug that the coil plugs in to. I figured this would do the job. I replaced the part,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Woolwich Twp., NJ
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
one of the burners was not working, the terminal block that the burner pluges into was burnt
I followed the instructions given to me in the package and all went well. I cut the old wires off the burnt terminal block, stripped the wires, installed the wire nuts with the shrink rap, installed the new terminal block and burner. The new burner is working great! Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paula from Dyersburg, TN
- Parts Used:
- WB30M1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Melted plastic colander on a burner
I simply replaced the element. HOWEVER, the most wonderful parts of this repair...Because of the pictures and closeups and descriptions I knew exactly 'what' to order! And I had the replacement in less than 24 hours. I can do some home repairs but this company provided such detailed information AND speed of delivery...that this was a no-fuss fix. I'll definitely stop by to buy, again. Thanks!
Was this instruction helpful to you?
Thank you for voting!