JHP62GN4AD General Electric Microwave Oven Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from VINELAND, NJ
- Parts Used:
- WB21X36771
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Electric Burner Control Broken
New one a little different ,but it was marked for wiring!
Had to install upside down because wires would not reach right side up!
Had to pull back side of knob out and turn 180 degrees and glue in knob, so knob would be right side up!
Works fine! Now all burners work again!
Had to install upside down because wires would not reach right side up!
Had to pull back side of knob out and turn 180 degrees and glue in knob, so knob would be right side up!
Works fine! Now all burners work again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Irwin from Tucson, AZ
- Parts Used:
- WB15X5163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic handle broke
There are two screws that hold the handle to to door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kathleen from broad channel, NY
- Parts Used:
- WB44X232
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Broil element snapped and went on fire.
I could not believe how easy it was to repair my own oven! Honestly I was shocked. I pulled the oven out, unscrewed 7 screws, pulled the old element out, placed the new one in, replaced the screws and I was done. All I could think about was how much money I saved! Also, it took me about 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from Lexington, KY
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Heating element had shorted out and broken.
Unscrewed the heating element from the inside back of the oven and removed the housing cover from the back of the stove to access the terminals. (The unit had arked and fused the terminal to the connector.) Installed the new unit and replaced the housing cover on the back and screwed the unit into the back of the oven. Works like a charm.
Was this instruction helpful to you?
Thank you for voting!
Surface Burners were very slow.
Removed old surface burners and replaced them by plugging in the new surface burners. Now they work GREAT! Parts ordered and received with-in 3 business days. Fed EX delivered parts in good order very quickly. We recommend PartSelect.com
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Hedgesville, WV
- Parts Used:
- WB2X9719
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
heating element clap broke off
All I had to do was pop the clamp on the top part of the heating element and push the clamp into the hole.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ervin from Milford, DE
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
infinite switch would not shut off at times.
First shut the power to the stove,then had to slide the stove out so I could get at the back to remove the panel screws.Once you have the back off remove the knob on the front.Under the knob is 2 phillips screws that you need to remove.Next I took the new switch and matched up the wires to the old switch.Reinstall is the reverse.Once the switch is in place you must remove the excess shaft to match the length of the old one.This is done with the use of 2 pliers,you grasp the shaft with both pliers and snap it off where you need it.The kit comes with spacers so you have got to match up the right one so the switch is solid on the shaft.This finishes the project,next turn the power back on and check that all is working ok.Job finished.
Was this instruction helpful to you?
Thank you for voting!
broiler element melted
pulled range out, unplugged unit, took out 7 screws, unplugged the elements, reinstalled elements, replugged, and completed with the 7 screws back in place. The 30 minute time was replacing both the broiler and bake elements. The parts were also delivered in a very timely manner. Could not have been more pleased and was very cost effective.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Kernersville, NC
- Parts Used:
- WB14X104
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven door hinge roller deteriorated, oven door hard to open.
Open and slide door upward off of hinges. Removed bottom drawer to access hinge spring. Detached spring, noting proper hole in hinge for reinstallation. Removed three screws holding hinge and removed hinge. Compared new part to old...exact match. Inserted hinge, and reinstalled the three screws. Reattached spring in hinge hole. Slid door back down onto hinges. Done in four minutes flat!
Was this instruction helpful to you?
Thank you for voting!
oven door jammed,could not open it
Removed old hinges and installed new hinges.
Hardest part was determining that worn hinges were the cause of problem, then ordering replacements. GE website hinge on exploded view did not look like hinges I removed.Thanks to Google I got on to PartSelect.com website where excellent pictures of hinges and one-inch grid confirmed they sold exactly what I wanted for my 13-year old range, the model number of which was not even on the GE website.
Hardest part was determining that worn hinges were the cause of problem, then ordering replacements. GE website hinge on exploded view did not look like hinges I removed.Thanks to Google I got on to PartSelect.com website where excellent pictures of hinges and one-inch grid confirmed they sold exactly what I wanted for my 13-year old range, the model number of which was not even on the GE website.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Perry from Flushing, NY
- Parts Used:
- F26T8-CW-4
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
remove and replace
very easy remove the bad bulb install the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RICHARD from SOUTHBRIDGE, MA
- Parts Used:
- WB8K5042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replace the light bulb socket.
Alls well that ends well. General Electric changed the configuration of our Light bulb socket on our 1996 oven. It did not have a flange with two screws as the original. The new one, you will just connect it and twist it into place. It worked and we are very happy. Such wonderful people to deal with at this site. Our sincere thanks,
Richard and Shirley
Richard and Shirley
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from PLANO, TX
- Parts Used:
- WB21X36771
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Old infinite switch WB21X36771 broke...heating element stopped heating
1. Bought replacement part said to replace old switch.
2. Pulled old switch out.
3. Replacement part did not match. Would have to take entire switch panel apart to change to this part.
4. Multiple-part instructions very poor. For my switch unreadable.
5. Old part was "push to turn". New part was not.
6. Knob did not fit new switch. Old shaft was "D" shaped. New is square.
7. Gave up. Need to call repair shop.
8. Hope this helps.
2. Pulled old switch out.
3. Replacement part did not match. Would have to take entire switch panel apart to change to this part.
4. Multiple-part instructions very poor. For my switch unreadable.
5. Old part was "push to turn". New part was not.
6. Knob did not fit new switch. Old shaft was "D" shaped. New is square.
7. Gave up. Need to call repair shop.
8. Hope this helps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Southern Pines, NC
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Surface element was corroded.
Removed existing surface element and replaced with new element.
P.S.
Part Select service was excellent.
P.S.
Part Select service was excellent.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- octavio from lake worth, FL
- Parts Used:
- WB44X232
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
broil unit caught fire and burned all the way around it
My great and talented hubby did it. He can fix anything. It was easy for him.
I love this website to purchase parts. Both times I have ordered something from you, it has been at a reasonable price and I received it really quickly.
Thanks!
I love this website to purchase parts. Both times I have ordered something from you, it has been at a reasonable price and I received it really quickly.
Thanks!
Was this instruction helpful to you?
Thank you for voting!