Models > FGMC2765KBB > Instructions

FGMC2765KBB Frigidaire Microwave Oven Combo - Instructions

Jump to:

All Instructions for the FGMC2765KBB
16 - 30 of 37
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Jacob from Ludowici, GA
Parts Used:
5303319559
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Microwave would not turn on
To determine which switch was bad, I removed all three switches from microwave. I used a D-cell battery taping two pieces of wire to the POS and NEG ends. Tape the POS end of wire to a flashlight bulb's bottom tip. Tape or twist the NEG end to the bottom of the switch. Connect another piece of wire to the top of switch and touch the side of the flashlight bulb with the other end of the wire; the bulb should come on. Depress the red button on the switch and the light should go out. The switch is good if this occurs. If light does not come on or the bulb does not got out once the red button is depressed, the switch is bad. Now you have determined which switch to order for replacement.
5 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from UNIVERSITY PL, WA
Parts Used:
5304485407
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Internal door open lever broke
Remove microwave from wall, removed outer cover which allowed access behind the control panel, was then able to take out the broken lever and with a little maneuvering was able to replace it with the new one. The whole process took less than an hour and was easy to accomplish.
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Tanya from KALISPELL, MT
Parts Used:
5304409888
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
The elements were not heating up
It was really easy just unplugged it took off the back cover changed the part out put back cover on plugged it in and the elements were working great!
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Larry from COZAD, NE
Parts Used:
5304524341
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Lens cover for the oven light
Very easy just had to pull the wire up that holds it secure.
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Daniel from MINNEAPOLIS, MN
Parts Used:
5304441893
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Push Button does not open door very well because door latch plastic is starting to split
Plastic trim on inside of the door pops out if you pry with a flathead screwdriver. Then lift door latch out of place and carefully remove the spring. New latch goes back in the way the old one came out. Door trim pops back in.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Daniel from Falmouth, MA
Parts Used:
5304409888
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Wrench set
Oven wires arced and caused the terminal block to melt and become detached from the back of the range
Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely.
Once all was replaced and reinstalled the oven has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Alan from SAN MATEO, CA
Parts Used:
316538904
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Repaired Oven Range Light Bulb
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Barbara from WICKENBURG, AZ
Parts Used:
5304409888
Difficulty Level:
Very Difficult
Total Repair Time:
30 - 60 mins
wrong part
my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as well as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from PLANO, TX
Parts Used:
5304503439
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Hardboiled egg cooked in microwave and exploded
0. Turn off breaker to oven
1 Remove two screws holding oven into enclosure.
2. Remove trim piece from bottom.
3. Open oven door, and engage part on hinge which keeps door from closing all the way. Now, door can be lifted and removed, set aside.
4. Slide oven out. This is very heavy, and it's best to have two people as well as something slightly lower than the oven to put it on, I used a chair.
5. Remove microwave trim, 4 screws.
6. Remove baffle which protects microwave power cord.
7. Loosen 4 screws from bottom of microwave. I used a Screwdriver bit with a pliers, as there isn't much room. Slide microwave forward or back, and microwave can be lifted from oven.
8. Remove 4 screws on side, 2 security Star screws on bottom of back, and 3 regular screws on back.
9. Remove top heat shield, and top/sides cover. Danger, do not plug in microwave with top/side cover missing. Also, capacitor on right/back may hold dangerous voltages, short the terminals using well-insulated tool. There is a bleed resistor which is supposed to do this, but you can never be too careful.
10. Open microwave drawer. Unscrew the front control panel from the inside. Remove plastic part the door open button usually moves, the part needs to be pulled to the left side to be removed. Take a picture of the wires attached to the switches on the latch plate, so you put them back correctly.
11. Remove wire connectors from switches. These connectors have a retaining feature, if you push the retaining feature, it doesn't take too much force to remove it. There are 6 wires. Remove the latch plate, there may be a screw or two.
12. Take note of which switches are normally own and normally closed. They have to go back the same way. I mainly took out the latch plate because the switches stopped working, a couple had welded themselves together internally. But, I had to replace the latch plate because I improperly removed the switches and broke the plate. The switches are held in place by a pin through the switch, a couple of static parts from the latch plate, and a tab which sticks up from the bottom of the latch plate. The pin is very fragile. Depress the tan from the bottom of the latch plate, and the switch should rotate on the pin. Do not release the tab until the such has rotated past it. Now, you can lift the switch.
13. Reverse all of these steps with the new patch plate to put everything back together. You might want to test the microwave before reattaching it to the oven.
14. To put the oven back into the cavity, it's best to lean the back edge over the bottom of the cavity, then lift the oven from the front and slide it in.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from Waynesboro, PA
Parts Used:
5304493153
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Everthing works except heating.
This is an OTR microwave oven, needs to be removed to diagnose problem. I did not diagnose problem properly, I searched online for possible causes, read that (99%)percent of the time the interlock switch was bad and replacement should solve my problem. It was also stated to be an easy fix,15- 45 minutes depending on ability. I ordered the relay switch. Took the oven down then removed outer shell. With my multimeter I began to test, fuses(2), interlock switches(3)and transformer. 3 interlock switches were ok, fuses were fine, and had power to the transformer, meter could not read output of transformer because of high voltage, (2300v). I'm down to magnetron (about a hundred bucks) or the touch pad/ circuit board. I have a countertop micro that I'm putting in place of the OTR. As far as Partselect, my item was shipped and delivered on time, instructions for changing that part was quite accurate. Would order from here again, just do my homework first.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Denise from Landover, MD
Parts Used:
316538904
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
light bilb went out
replaced it
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Betty from OLIVE BRANCH, MS
Parts Used:
318578506
Difficulty Level:
Very Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
Thermostat for oven cook elements. Cooling fan is a misnomer-the fan still worked!
First of all I am not Betty, I am her husband. Second I and a friend pulled the range out of the countertop (which was not necessary). The top can be raised on it hinges and the plate under the burners can be removed by taking out 8 to 19 screws and there is the thermostat looking at you. After doing this once and knowing where the thermostat is, the job could be done in less that an hour.. INSTRUCTIONS: Turn OFF the circuit breaker. Remove the burners. Remove the plate under the burners. Change the thermostat (making sure to place in correct direction as the one removed). Reassemble, turn on circuit breaker, test oven heat.
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mary from EDGAR, WI
Parts Used:
5304504897
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
sensor should pull into oven enough to easily unsnap and snap but didn't pull out
on the back side of the wall oven the sensor wire was ziptied tight. we had to totally pull oven out of its wall space, remove back panel, unhook zip tie, feed through sensor hole around insulation, connect and then replace back and return and relevel the oven. I have
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Tony from Hartford, CT
Parts Used:
5304409888
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
No Power to the Oven
Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Selma, CA
Parts Used:
5304493153
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Wrench set
Microwave Would Run And Count Down But Not Heat
Removed unit from above stove removed outer housing, interior shield and tested the 4 door relays. One was not working. Replaced parts and re installed unit over stove.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the FGMC2765KBB
16 - 30 of 37