Models > GLEB30M9ESC > Instructions

GLEB30M9ESC Frigidaire Microwave Oven Combo - Instructions

Jump to:

All Instructions for the GLEB30M9ESC
61 - 75 of 106
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
John from Selma, CA
Parts Used:
5304493153
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Wrench set
Microwave Would Run And Count Down But Not Heat
Removed unit from above stove removed outer housing, interior shield and tested the 4 door relays. One was not working. Replaced parts and re installed unit over stove.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Douglas from Colrain, MA
Parts Used:
318328010
Difficulty Level:
Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
had no instructions on how to remove old door hinge recepticle..
After trying to unscrew a plate on the side, I found that would NOT work at all, the side panel of the stove was behind it. I found a tab that cut-out on 3 sides just above the location of the recepticle, and simply bent that tab out, pulled out the old recepticle, slid in the new recipticle, and put in the screws and then bent back the tab. It was sooo easy once I found that. I repeated in on the other side.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
adam from new orleans, LA
Parts Used:
5304493153
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Power, light, and clock work, micro/turntable not working
Much like the other post: 1. Removw vent case on top (3 screws) 2. Remove cover with control buttons (1 screw). 3. Removed bottom relay switch and replaced. Tight working space so be patient. Took 15 minutes Needle nose pliers used to crimp connector onto switch
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Harry from Cypress, TX
Parts Used:
5304493153
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Instructions did not match the assembly of the ice maker.
I managed to move the auger far enough to allow me to insert the cup-drive and then realign the auger with the new cup-drive. I also have had one to break very shortly after installing it. This is my second part to replace and this one went really smooth, since I understood that the initial parts installation instructions did not apply on my ice maker.
0 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sue from Lampasas, TX
Parts Used:
5304409888
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
Control will not work - only clock blinks
Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.
0 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sharon from Foley, AL
Parts Used:
5304524341, 316538904
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Broken globe in oven and burnt out light bulb
Easy as 1-2-3
0 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gary from Reno, NV
Parts Used:
316270201
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
handle broke
unscrewed old and screwed in new
Was this instruction helpful to you?
Thank you for voting!
Customer:
CARL from MARSHALL, WI
Parts Used:
318053120
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
burnt door seal
with a schematic of the door, this was fairly easy. since we had to take it completely apart, we cleaned the glass as well and every little nook and cranny. Once we put it back together, the door looked like we just bought it. these days, with whats available online, scary jobs turn out to easy.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Krista from Newtown, CT
Parts Used:
5304503232
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
inner glass uncleanable
Took door apart, went online to partselect, ordered new glass, and put it back together. Oven looks like new. Makes sense to order the isolation as well when you do the repair
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jim from Franklin, TN
Parts Used:
318254906
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Uneven bake temperature
I removed the element, plugged in the new one and that has corrected the uneven oven temperature.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sandra from Magnolia, TX
Parts Used:
318053120, 316217002
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Oven would not reach temperature
Husband made install in very short time. Nice to have them back in operation.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Hemet, CA
Parts Used:
5304503232
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
really bad ugly streaks inside of glass
open door,throw the door latches at the hinges and remove door. Take the out of the outer panel so you can separate the glasses. remove clip that hold the outer glass in place. I ordered a replacement glass as I never thought that it would come clean it looked so bad, but it cleaned up like new so I now have a spare glass for my oven door. Just reverse the way you take it apart to put it back together.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from Oro Valley, AZ
Parts Used:
318255605
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
broiler element burned out
watched a U-Tube video on this subject.....worked like aa charm!!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from Glasgow, MT
Parts Used:
316217002
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Oven was not heating up to the set temperature. Stopped around 180-200F.
Removed 2 screws holding old temperature sensor inside the oven and gently pulled out the wire till the connector came through the hole. Disconnected old probe and attached new one. Fished the wire back in the hole and replaced the two screws. Then followed the operating instructions for calibrating the oven. Ended up setting it +5 degrees. So far, works great.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Chad E from Newmarket, VA
Parts Used:
5304440845
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
microwave was sparking
Easy fix for my microwave. The cover just slips out, no tools needed.The best part about this fix was dealing with PartSelect. I recieved my part in less than 3 days but it was damaged. PartSelect overnighted a repacement and I am back in business.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GLEB30M9ESC
61 - 75 of 106