GLEB30M9FBB Frigidaire Microwave Oven Combo - Instructions

Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.

I removed the element, plugged in the new one and that has corrected the uneven oven temperature.

Really straightforward - just took door off of the hinges and worked taking it apart until I got to the front glass that was cracked. Took it out and put the new piece in and reversed the process. Really easy and I got to clean each piece on the way back in to get rid of some spills.

Removed 2 screws holding old temperature sensor inside the oven and gently pulled out the wire till the connector came through the hole. Disconnected old probe and attached new one. Fished the wire back in the hole and replaced the two screws. Then followed the operating instructions for calibrating the oven. Ended up setting it +5 degrees. So far, works great.

watched a U-Tube video on this subject.....worked like aa charm!!

After searching to find the right part to replace this i found this company on line. I still could not find the part so contacted them directly and the nice woman who answered found the exact part we needed. It was shipped to us in perfect condition and we did the install ourselves with the installation help that was included with the part. We are so thankful we found this company and were able to fix our broken door. Would recommend them very highly.

Moved the stove away from the wall, unhooked the electric cord and the gas pipe. In the oven, undid the two screws holding the probe. Removed two screws and removed the electrical cover panel from the stove back, disconnected the quick connect to the probe and pulled the probe from the oven. Reversding the proceedures, put the new probe into the oven, hooked up the quick connect and replaced the electrical panel cover. From the front, reinstalled the probe with the two screws, reconnected the gas and the power cord and put the stove back into position. It works just fine now!

Just slide the cover up a bit and it comes out. put the new one in place and slide down into place. done that's it.

Googled the problem and found Oven Temperature Sensor and Main Terminal Block to be the most likely problems. Turned out to be neither. No parts were needed. Oven has a thermal overload switch on the rear upper left. Thermal overload needed re-set. To do so you have to remove the oven, remove the back and press the red button on thermal overload. Biggest challenge was figuring out how to remove the oven. Even with the installation manual it was not easy to fgure out. The instructions are misleading. You need a special tool. I used two hacksaw blades as a substitute, and slid them in to release the clips. Once you figure out how to get the oven out the rest is simple.

Removed outer glass first ,then worked my way thru to inner glass..

1. Moved stove from against the wall. 2. Unplugged the power supply. 3. Removed the electrical pannel cover. 4. Disconnected the quick connect probe plug. 5. Opened the oven and removed the probe. 6. Installed the new probe. 7. Connected the quick connect plug. 8. Reattached the electrical panel cover. 9. Plugged in the electrical supply. 10. Moved the stove back into its original position. ****Note**** THIS IS THE SECOND TIME I REPLACED THE PROBE. THE FIRST REPLACEMENT LASTED ONLY 5 MONTHS!!!!

I actually watched Youtube while I was changing it. This video was not actually the same make up of my oven, even though the I typed in the model number. I manage to figure it any with the steps anyway. It was harder then I expected but not horrible. I think I did pretty well for a women. Patti

Took door apart, went online to partselect, ordered new glass, and put it back together. Oven looks like new. Makes sense to order the isolation as well when you do the repair

with a schematic of the door, this was fairly easy. since we had to take it completely apart, we cleaned the glass as well and every little nook and cranny. Once we put it back together, the door looked like we just bought it. these days, with whats available online, scary jobs turn out to easy.

I noticed that the scorched and slightly melted plastic was above a little piece of what looked like cardboard, so I did a Google search for "flames in microwave" or something similar and found a link to a DIY repair site that mentioned a tear in the waveguide cover causing that problem. I ordered a replacement from PartSelect, received it in near-new condition, and replaced the old one with the new one in 5 seconds. I then called PartSelect to let them know that the new part had a couple of "wrinkles" in it that I was concerned might cause a problem down the line but that it seemed to be working OK for now. The nice person in customer service told me that I could use the part for the full year of the warranty and return it if a problem arose. I'm very satisfied with the experience!