EHS346 Caloric Microwave Oven Combo - Instructions

Removed old block , cut off wires , used new wire nuts, heat shrink , supplied with parts , job done lowered range top went fishing ...

One screw taken out, 2 wires switched, new part & screw put in. Burner like new!

Replace the connector and bracket, spliced the wires, put heat to the schrink wrap and I was done.

I raised the stove top, read the instructions to my son while he did the work, then I lowered the stove top, installed the burner, and it worked like magic.

I just installed the new burners into the proper place and they fit This was very easy to order. Just had to find the model number which the web site told me where to find this. I am very satisfied with the service Thank You

Cut the two wires approx 1 inch behind old connector and removed one screws to remove old connector, stripped approx 3/4 inch off the wires and connected them to the new wires on the new connector with wire caps and shrink wraps which came with the new connector. Replaced the old screw with the new screw and the job was completed. Be sure and disconnect power before starting!!

Read instuctions first Turn breaker off to stove or unplug to be sure. Remove burner and drip pans. Remove scews holding socket in place if you are doing more than one make sure you keep in same location. Raise cook top untill supports latch in. Assemble plug it comes with two types holder compare to your plug. cut wire to old plug so you have enough wire to connect back with new. Strip wire back and place shrink tubeover wires wire nut together heat with a lighter or heat gun then do remaining plugges. place back in cover and replace scews. make sure wire are not to long to get under burner when cook top lowered. Lower cook top and clean burner plug ends with a little sandpaper to make sure they make good connection. replace pans and burner. turn on breaker or plug in stove making sure the burners come on when turned on good luck g.d.

shut off circut breaker. un pluged stove removed back panel disconected 2 wires on element. removed 1 screw that holds element in place pull out old element put in new reassemble

I had no trouble replacing the Broiler heating element, total time 30 minutes. Just had to pull the range out to unplug it and remove the back sheild of the range, then remove the two push on electrical connections. Then removed one screw holding the element to the inside of the oven, replaced with the new element, attached the connections, but the back sheild back on and it was done.

I noticed that one of the burner blocks was completely burned and the others were corroded. I ordered blocks for all four burners. Installation was easy except for one block. The screw holding the bracket to the range top was completely corroded in place. I used a correct size easy-out, which is a left hand tap and drill, to remove the screw. That took about five minutes, including tracking the easy-out down in one of my many toolboxes. The entire replacement of four blocks took about one and a half hours. Stove top cooks like new on all burners! The part kit had all the right parts and they fit like a glove!

After turning off circuit breaker to the stove, I removed all surface units , removed the 4 screws holding the top and lifted up. The plug in was burned out (the wire was burned). Look at the old plug-in so as to be able to match the new one and insert the pre- crimped end of wires into the block and the block into the metal holder that matches your old one. (The kit comes with 2 different metal holders)After this, cut out the old wires and wire nut the new wires with the stove wires. Put shrink wrap protector on the wire nuts and heat to shrink it tight.attach the block to the stove top and wa la its done. Very easy.

I read instructions and hints online. Then, I pulled the range out from between the cabinets and unplugged it (carefully). I used a small Philips head screwdriver to remove the 10 metal screws holding the large metal sheet on the back of the oven. Then I removed the 4 screws holding on the metal sheet on the upper level of the back of the range since it had to be removed to move back the big sheet metal away from the back. The large metal sheet has the power cord threaded through it on the bottom and I left that in place. I then removed the oven door by lifting it up off the hinges after I removed the screw on each side that held the door on the hinges. The door is quite heavy for a girl. I unscrewed the plate at the back of the broiler element, unhooked it from the hangers, and carefully pulled the connectors apart from the oven wiring and the dead broiler element. (Being completely unfamiliar with this kind of connector it took me some time to figure out they slid apart.) Following advice online I had used electrical tape to tape down the wires so they wouldn't slip backwards out of the oven. The new broiler element connectors slid smoothly and easily into the oven wires. I removed the electrical tape I had used as temporary holders, hung the element on the previous wire slings and removed the new wire slings for a backup. I screwed back the plate on the new element into the back of the oven wall. I used the part number orientation on the element to make certain I had it right side up. If I have to do this again it will be easy and take very little time. My biggest problem was getting the oven door back on because it was heavy for me and I was too short to be able to see what I was doing as I repeatedly tried to get the oven door and hinges aligned. Eventually the door was back on and screwed down. Everything that had been unscrewed was put back in place and screwed down tightly. The oven and broiler are working perfectly.

Description of the element indicated that it would work for the oven burner. However, it obviously was meant for the broiler element. I had to remove the thin metal piece with the attachment holes in it (the holes didn't match the holes in the back of the oven). To install I had to drill two holes in the remaining attachment flange to match the holes on the back of the oven. Then I made three metal supports out of sheet metal to hold the element up approximately 1 1/2" off of the bottom of the oven. Just thankful to find one that I could make work. Oven works fine now. LF

I removed the burner element, then the drip pan. I took off the old block. Then I had to strip the old wires. Then I put on the heat sleeve, then attached the new wires to the old wires with nuts. Put heat sleeve over this and heated with lighter. Then put everything back together.

Ordered wrong part at first caused me to blow out two elements. With the help of PartSelect I was able to get the right surface block terminal and replaced both of them, then found out I had a bad switch, they got the switch within 2 days I had my stove working good again. Thanks to PartSelect. Also watched the video which was very helpful ML