YMEDB700VQ0 Maytag - Instructions

The door catch dislodged in the door and apparently broke. The hardest part was getting it out of the door because in trying to remove it, the piece fell into the inside of the door. I could have easily just installed the new part (it snaps right in with great ease, that part took exactly 5 seconds). But hearing that old piece rattle around inside the door would have made me a little nuts. So I decided to take the door apart to retrieve it. It was just a bunch of screws from around the perimeter of the door, but I also had to unhinge it to do the job. Putting the door back together wasn't as easy as I had hoped, with some pretty tight fits and the glass dislodging. Had a few moments where I was regretting. But I got the old part out, snapped the new one right in. I'm sure an appliance guy would have charged me $60 - 90 just for coming out. Instead I repaired the dryer for the cost of a $3 part. One small lesson learned here -- dryer doors are much like refrigerator doors, or at least mine is. There is a door catch on both sides of the door so you can hinge it to open either way. I could have done the repair for nothing! But I love parts select for just this reason. I don't do major repairs, but replacing pieces on appliances couldn't be easier with this service!

Replaced Lint Screen

Had previously replaced the heater coil (purchased from PartSelect) and fixed the no heat problem. Should have taken advice given on this site and replace the thermostat and thermal fuse kit at that time. Since I knew how to remove the assembly it was easier this time. Just remove, unscrew the two parts and replace with the new ones. Reattach the wires and reinstall the assembly and it is now working again. Also vacumed the inside and trimed and replaced the exhast vent hookup for less restriction.

After trying to follow a very detailed description by another consumer, we googled our washer and found a site that showed step by step direction that took us through removing all panels and getting to the bellow easily. Not removing the proper panels, we found was making the job hard!I believe the site was applicance services...very helpful! Step by step literally!!Cost of parts through parts select reasonable.

pulled out old lint filter. Put in new lint filter.

Turned off power and pulled power plug from the wall. Removed the two screws at the lint screen. Raised the top to by depressing the top spring clips. Removed the two 5/16" screws from front top. Removed wiring clips from front panel. Set the front aside while I removed the two broken panel clips. Installed the two new panel clips. reinstalled the front panel by placing the front panel above the sides. Opened the front panel door and supported the drum while allowing the front panel to slide down onto the new front panel clips. Reinstalled the wiring clip. reinstalled the two 5/16 screws. Turned the drum to ensure that the felt seals and drive belt weere installed properly. Lowered the top and reinstalled the two screws at lint screen. Reinstalled power plug and turned on power. No rattles or squeeks!!!

As in the video: inserted putty knife behind catch lip above and below the catch. Video shows only doing on top or bottom, but need to do both and then pry out while pushing towards the center of the catch up and down. Not as easy coming out as in the video. Putting new catch in was easy...just slide into hole.

Followed standard instructions regarding removal of top first & then the front panels. Realized after following this process that I did not have to remove top, but only one of front panels to obtain access to moisture sensor. If I have to do this again, the replacement of sensor will be much easier.

I watched the video, took a knife and released the outer catches on the stainless steel spring clip, but part of the broken catch was inside the clip crossways and would not let the clip come out. I had a set of hook shaped picks (from Harbor Freight) and I tried to pull out the broken piece, but it fell inside the door. I was then able to pull out the spring steel clip, and push the new part in and it caught. I left the broken parts inside the door, thinking it would not hurt anything. Door latches OK now.

Popped the old catch out (but was not as easy to get out as described) but did pop back in very easily! The video was a great help!

remove&replace

popped old catch out put new catch in

As showed in the video, it was simple. Popped out the broken catch and popped in the new catch, less than a minute. Thanks for the video.

Dryer is on a pedestal. Opened drawer and removed two 1/4 inch screws on bottom panel of dryer front. Panel drops down and exposes the dryer exhaust where thermistor is located. Removed two spade connector wires and removed two 1/4 inch screws. Installed new thermistor and reversed procedure. For the moisture sensors I used a phillps screwdriver and stuck my head in the dryer and removed the lint screen assembly (3 screws). Removed the spade wire connectors and used a straight blade screw driver to remove the moisture sensor. Installed the new sensor and re-installed the lint screen assembly in the reverse of removal. All very easy - just took 30-45 minutes total.

Watched steve on the video on changing the thermistor a couple times, it appeared to be straight forward replacement. Unplugged the dryer. . . Went through the front, my lent filter slides in and out from the lid so I had too remove two extra screws to detach it. After opening up the front it became very apparent my thermistor was not located in the same location as the one in the video. Dryer needed a cleaning (lint/dust) so I released the idler pully tension on the drum belt and went ahead and removed the drum/belt and shop vac/ blew with compressed air and shop vac once again. Gave my dryer a much needed cleaning since I had it apart. Put everything back together in about 20 mins. Pulled the dryer away from the wall and removed rear cover and presto there it was right next to the dryer air outlet. Replaced thermistor and replaced back cover, inspected out flex hose on dryer outlet, I clean it out (flex) yearly to prevent problems. Reattached flex on both ends, re-positioned dryer, plugged back in, and works great! Definitely fixed my problem. . . Replacing the drum by myself was a bit difficult. Still do able (there's a video on that also. . )