Models
>
MLG23PDAGW
MLG23PDAGW Maytag Dryer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for MLG23PDAGW
Viewing 12 of 12
.gif "CONTROL CENTER Diagram and Parts List for Maytag Dryer")
Keep searches simple, eg. "belt" or "pump".
$22.91
This OEM drum support roller kit contains the parts needed to replace one roller on your dryer. This kit includes one drum roller and two bearings. Most dryers use two drum rollers, and it is recommen...
In Stock
Order now and your part arrives by Apr 23
$13.07
This part is located on the front bulkhead of the dryer and helps the drum to rotate smoothly and quietly. If you notice a screeching or metal-on-metal noise while your appliance is operating, you may...
In Stock
Order now and your part arrives by Apr 23
The roller shaft is also known as a support roller shaft or a drum roller axle. It is a part in your dryer that the drum rollers spin on, helping your dryer to tumble. If your appliance is noisy while...
No Longer Available
If your dryer is noisy while operating, or will not tumble at all, there may be an issue with the drum belt. Over time, the rubber can become brittle and snap, and the belt will need to be replaced. T...
In Stock
Order now and your part arrives by Apr 23
$6.51
Sometimes referred to as a retaining clip, the retaining ring is used to hold the drum support roller onto the shaft in your dryer. The clip may need to be replaced if you find that your dryer is nois...
In Stock
Order now and your part arrives by Apr 23
If your dryer is making excessive noise, or it will not tumble, there may be an issue with the idler pulley wheel. The idler pulley wheel is attached to the idler bracket and is used to secure the dry...
In Stock
Order now and your part arrives by Apr 23
$36.42
This genuine OEM part is a radiant flame sensor for your gas dryer. It is used to determine when the temperature of the igniter is hot enough to ignite the gas. Once the igniter is hot enough, it allo...
In Stock
Order now and your part arrives by Apr 23
$13.07
This roller shaft washer is just under an inch in diameter and is used for some of Whirlpool's brands of clothes dryers.Sold individually.
In Stock
Order now and your part arrives by Apr 23
$28.91
This flat style igniter comes with a wire harness connector. This part ignites the gas within the dryer. Bracket is NOT included.
In Stock
Order now and your part arrives by Apr 23
$13.07
This idler pulley shaft washer is used with many clothes dryers. It is less than an inch long, and it is black in color.
In Stock
Order now and your part arrives by Apr 23
$19.63
This seal can be used for the front or rear drum. Adhesive is NOT included. For adhesive search: WPY055980
In Stock
Order now and your part arrives by Apr 23
In Stock
Order now and your part arrives by Apr 23
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for MLG23PDAGW
Viewing 9 of 9Noisy
Fixed by these parts
How to fix it
Door won’t close
Fixed by these parts
How to fix it
Marks left on clothes
Fixed by these parts
How to fix it
Drum Not Spinning
Fixed by these parts
How to fix it
Not Heating
Fixed by these parts
How to fix it
Too hot
Fixed by these parts
How to fix it
Touchpad does not respond
Fixed by these parts
How to fix it
Door Pops Open
Fixed by these parts
How to fix it
Door latch failure
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- gerald from park city, MT
- Parts Used:
- WP6-3129480, WP33001443, WP312535, 12001541, WP9703438
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
dryer squeeking
removed front panel,lifted top, removed drum and drive belt,remove old rollers and acc and instlled new and reinstalled dryer parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Osvaldo from Albuquerque, NM
- Parts Used:
- 4391996
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Dryer Stopped Heating
If everything else is working ( tumbler and timer ) except for the heating. Your first bet would be checking your flat style igniter. Mine was cracked, something that I wouldnt have seen unless I had taken it off. Because of the crack no current was being passing through, therefore the igniter wasnt heating to its amber color. Since
... Read more
there wasnt any current the gas valve was doing its job by not allowing any gas to blow out. Dont worry about turning the gas off just disconnect your elecrical outlet. Remove whole front dryer panel by taking 2 front bottom screws out (philip screw driver). Dont pull to hard because there are two wires connected to the panel and dryer that you will have to disconnect. When you get to the igniter disconnect wire plug and use your socket set to loosen the single srew on the igniter, gently wiggle it out by just handling the white ceramic part of the piece, and replace new one in. Just remember to be careful since the dark part of the igniter that heats up is real brittle.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teresa from Pace, FL
- Parts Used:
- WP33002032, WP33001755
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
dried too many shoes and broke the baffles
removed door, removed screws to lift top panel, removed screws that held old baffles, replaced with new baffles, took off front panel and cleaned out excess lint while I was in there.
Was this instruction helpful to you?
Thank you for voting!