YTH24V54-96043025900 Husqvarna Lawn Tractor - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Wheel bushings were bad
Removed old clip removed rim from tractor, removed grease fitting on rim, took hammer and screw driver knocked out old bushing turned rim over knocked out other bushing. Press in new bushings reinstalled grease fitting slide tire back on tractor, put retaining washers on then locking clip put on dust cover grease at grease fitting. Repeat other side.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- D from HUNTSVILLE, AL
- Parts Used:
- 84001919
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Engine quit due to valve guide sliding out causing rocker arm to be immovable resulting in bent push rods.
Clean engine with a Gunk type product. Remove valve cover. Loosen bolts and remove old cylinder head. One bolt is located inside valve cover area. Remove old gasket and inspect and clean that surface. Attach new head with new gasket using existing bolts. Torque to 18'#s with a cross type pattern. Attach new rocker arms and push rods. Set valve clearance to .004 - .006. Attach valve cover with gasket. Check oil level. Start and let it warm up. Let cool remove cover then check valve clearance again. Replace cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from SAINT JO, TX
- Parts Used:
- 797242
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Rod broke ruining the case and camshaft
dissembled ordered repair parts, piston ,upper case, rod, camshaft, seal kit, and motor maintenance CD
The camshaft first provided did not have the compression release device on it and the cam lobe position was all wrong for the model engine I had. .
Parts Select provided me with the proper cam Shaft. Removed engine from mower (Scag Freedom Z) 15 minutes, drained oil, flipped upside down removed bottom case, removed wrong cam shaft, reinstall new valve lifters, camshaft with decompression release on it matching dots on crankshaft. Used paint brush to coat all parts heavily with motor oil.
Do not put sealant on case gasket,(it might change crankshaft end play), retorqued bolt in alternating pattern, placed nylon pipe tape on drain plug threads, and reinstalled engine on mower. It started instantly and ran extremely smooth with no oil burn or vibration.
I am very happy with the support and quick mshipping Parts Select provided..
The camshaft first provided did not have the compression release device on it and the cam lobe position was all wrong for the model engine I had. .
Parts Select provided me with the proper cam Shaft. Removed engine from mower (Scag Freedom Z) 15 minutes, drained oil, flipped upside down removed bottom case, removed wrong cam shaft, reinstall new valve lifters, camshaft with decompression release on it matching dots on crankshaft. Used paint brush to coat all parts heavily with motor oil.
Do not put sealant on case gasket,(it might change crankshaft end play), retorqued bolt in alternating pattern, placed nylon pipe tape on drain plug threads, and reinstalled engine on mower. It started instantly and ran extremely smooth with no oil burn or vibration.
I am very happy with the support and quick mshipping Parts Select provided..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from LAKEVILLE, MA
- Parts Used:
- 532439870
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
Original shield was damaged
Removed original shield ( 2 bolts), replaced with new shield.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from CANBY, MN
- Parts Used:
- 587820301
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Socket set
Worn out Mandrel Assemblies
Remove Deck, Remove Blades, Remove guards and belt, use old belt to hold pully to remove pully (would be good to have pully wrench), Remove mandrel Assembly, Install new mandrel assemblies (had to tap the new mandrel assemblies. Should have been done by manufacturer.). Reinstall blades, guards, and belt. Put deck back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MATTHEW from PENNSBURG, PA
- Parts Used:
- 587686701
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Right axle bent
Replacing belt with no problem. I've ordered the front right axle spindle assembly three times. This is from your parts list and you sent me the part and they did not work at all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tamara from Iuka, MS
- Parts Used:
- 547634701
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Console assembly broke
Underneath the console is a 10 mm nut took it off slip the grip off and installed new console took less than 5 min very easy repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from PILESGROVE, NJ
- Parts Used:
- 532123583
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Take the wheel off. Place the key in the slot. Put the wheel back on.
Just described it.
Was this instruction helpful to you?
Thank you for voting!
Dryer runs no heat
Disassemble dryer. Replaced element assembly. Re assembled dryer. Unit runs and heats.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frederick from BINGHAMTON, NY
- Parts Used:
- 532121749
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Front wheels, too much end play
Shimmed the wheels out on axle.. No more slop.
Was this instruction helpful to you?
Thank you for voting!