JMV8196ACW - Instructions

I started by calling a reputable service company to diagnose my problem. The repair tech told me it was the magnetron and it was a "very difficult" repair that required two people because the over-the-range unit needed to be taken down. I asked for a detailed estimate. He quoted $550 including parts and labor. After he left, I researched the part costs on this site and realized his costs were very inflated. I purchased the magnetron for $220. It arrived at my door two days later. Installation was very easy. First, I unplugged the unit. Then, while my wife was making sure it did not fall off the wall bracket, I unscrewed the two mounting screws from the top of the cabinet. I lifted the unit down from the wall and set it on the kitchen counter. The shell needed removed from the microwave which involved about 20 screws. This provided access to the magnetron on top. The magnetron is secured by five screws and a plug. I unplugged it, unscrewed it, and removed the old part. Then, I installed the new magnetron, and tested the microwave to make sure this did the trick. It worked. I put the outer shell back on the microwave and cleaned the microwave. (This is a great opportunity to clean the areas you do not typically see!). I then remounted the unit and plugged it back in. Saved myself a bit of money so I took the family out to dinner and a movie to celebrate. Microwave was in working order for heating up left overs the next day! Thank you!!!

removed old cover to lamp and reinstalled the new one by unscrewing one screw and screwing the new one back in

I unscrewed the light cover, removed the burned out light bulb and replaced it with one I ordered on Partselect.com. It was very easy.

Since others reported similar problems and it was just the fuse we tried that first. That wasn't the problem so we ordered the Door Interlock Switch Kit. Shipping was very fast! Our microwave had 3 switches. My husband asked how to know which one to switch. I read that one person just did process of elimination. Luckily ours worked on the first change out! So happy to have stumbled across this site and not have to buy a whole new microwave.

After unplugging the microwave and removing the screw, I removed the old bulb and put in the new one!! I made sure it was in securely and the difference in the light was awesome! I use this light when I bake bread and let it rise inside the microwave, but DO NOT turn it on. The heat from this light helps the bread to rise properly!!

The problem I have with changing the bulb is my microwave is an overhead one and therefore I cannot tip it on its side to easily replace the bulb. I have to drop the lid down and carefully install the new bulb from underneath.

removed grill cover, removed bulb plate, unscrew bulb, screw new bulb in socket,put bulb cover back on and screw grill cover back on. no issues whatsoever.

All the electrics worked on Amana microwave EXCEPT for the cooking function. Inspected the control board and found the upper switch on the door interlock was burnt. Installed new switch in minutes and everything now works fine. Unfortunately, had to purchase expensive two switch "kit" although only one switch was kaput. PartsSelect mailing was SUPER fast. Thanks for looking, Scott

My wife was pushing a few buttons with her knuckle (hands were full)and the microwave just turned off. Just like we had blown a breaker. First I unpluged it. Then I removed the phillips screws of the front panel, and found and removed the ceramic fuse. 3 days later I received the new fuse in the mail, and put it in. I plugged the microwave back in and it works great.

The door was not engaging the micro switches properly no doubt from 10+ years of wear. The upper switch removed fairly easily but take care not to tweak the plastic brace too much or it will snap. The lower one was the tricky one. After much examination I noticed that the trick to remove it was underneath the brace. Take a butter knife (no joke) and insert it just under the old micro switch and gently press down twisting the micro switch every so slightly til it releases. The replacements snap back in with no trouble. The microwave is working much better now, though not perfect.

I put in the filter. The "over the stove microwave" made installation so easy even a woman could do it!

It literally took me longer to unpackage the fuse than to install it. I removed the outer shell by unscrewing the five screws, lifted it off and set it aside. The old fuse was readily visible so I pulled it out and put the new one in its place. I set the shell back on and replaced the screws. I plugged it in and ran it for 30 seconds while still in the shop just to make sure that solved the problem and presto - it worked like a charm. A $20 part saved me from having to purchase a new microwave (sadly, I had to break the news to the wife).