JFI2089WES10 Jenn-Air - Instructions

Could not figure out why this was happening suddenly. Then remembered I had recently changed the lid to one I had stored for over two years in the garage. They had sent me a replacement lid when the unit was less than a year old because the origianl had a crack in the clear section. Noticed it seemed a little warped. Thought I would replace it to see if that solved the
problem.
We had to replace the side panel of the draawer because the warped lid had broken the peg off of one side. I didn't want that to happen again.
The new lid did the job....This company is the only one I will use in the future for my appliances. Very easy to find parts and the pricing was better.

1. removed both bottom crisper drawers
2. removed glass shelf under crisper drawers
3. removed shelf support pieces
4. removeded snack drawer
5. removed left slide rail using phillips screwdriver (2 screws)
6. removed LH end cap using socket wrench (3 screws)
7. attached new LH end cap
8. attached slide rail
9. installed glas shelf supports
10. installed glas shelf
11. install bottom crisper drawers
12. install snack drawer
13. install snack drawer top

total time was less than 15 minutes

Removed the three screws that held part, lifted and removed old part and replaced with new piece.
Couldn't have been easier. Saved me the $100 the repair man quoted me. Cannot believe it was so easy and the
part was soooo affordable! Thank you very much for the speedy delivery. It came within days of my order.
I will use your service again for sure!
Thank you!
Allyn Rosenzweig

The front had to be removed from old drawer a put on new one

Reviewed replacement instructions video on your website. Just followed the easy instructions to pop out old cover and pop in new cover. I would not have tried to replace it myself had I not seen your video. Super easy.

replaced the poorly designed "duck bill" drain with this P trap. Very simple repair done by accessing through the back of the refrigerator. The video on this website walked me right through the repair. It did however fail to mention that the ice has to be removed from the inside. I had to remove the drawer face and pull outs. Then the ice maker and back panel are removed. I used a heat gun and screwdriver to chip and melt the ice build up. If one had the luxury of having another refrigerator to move food in to you could just unplug the unit until the ice melts.

The other instructions and the video provided by Parts Direct are pretty good with instructions, but they omit two steps. First, if you have an ice maker, you will need to unplug the connector on the back side of the panel you remove at the back of the refrigerator to access the drain tube. Just unplug it and you can move the removed panel to the side without disconnecting any of the water lines. Second, the instructions say to just reconnect the "bottom end" of the new p-trap drain to the drain pan at the bottom of the refrigerator. They don't tell you there are two places to connect the new p-trap to the drain pan. The original tube/trough connected to the one at the back of the drain pan on the left (viewed from the rear of the refrigerator). At first, it looks like the new p-trap won't reach to it for the connection, but if you look closer, there is another connector to the right of the original one that the p-trap connects to properly. Replacing the drain trough with the new p-trap was actually pretty easy and would only take about a half hour. Add another half hour to give the refrigerator coils a good cleaning as they will need it now that you can reach them. The real time consumer, 3 to 4 hours, is needed to use a hair dryer to melt and clear the ice from the condenser at the back of the freezer so the water can drain. Just take your time and all the ice will eventually melt and drain out so the new p-trap will work properly.

Pulled the broken pantry door off, and snapped the new door in place. Vry simple.

We ordered the part by phone at about 4pm on Monday, and it arrived via Fed Ex at 10:30am the next day. WOW. My husband fixed it in about 5 minutes. Removed the old mullion with a socket set thing and screwdriver. Unscrewed the screw, slid the mullion up, disconnected a wider that is inside. Then he lined up the top and bottom plastic parts, reconnected the new wire, slid the new mullion in place, and screwed it on.

First, make sure you have the correct part. I had trouble with mine, at first, until I realized that I had received the wrong part... it was same shape but larger. To begin, remove both fruit/vegetable drawers. Remove deli drawer. Remove deli drawer glass panel with both supports. Remove 3, 1/4" hex screws that attach end-cap. Disengage temp control slide and arm from end-cap by carefully moving parts in the direction where they will disengage. Remove temp control slide from end-cap. Now that end-cap is out, remove 2 screws that hold metal drawer slide to end-cap. Attach drawer slide to new end-cap. Attach temp contol slide and connect the plastic arm. Attach end-cap to refrigerator. Replace glass shelf, supports and drawers. Done.

take the old one out replace with new once - no instructions required, no tools needed

one screw and electric plug and the unit slide out. Slide the new one in and your ready to go.

I didn't. Don't know how to get to light bulb to change it for this specific model

This kind of repair makes me love the internet. Thank you. Follow advice of my fellow posters but beware, all your plastic parts are very brittle from the cold. Proceed slowly. As mentioned by others but worth stressing is...do resist the temptation to force any piece...I could just see myself snapping one of these pieces and having to order another part! Take your time to work out the sequence to disengage each piece in turn. It's a bit of a puzzle but take your time. Also suggest starting the job with a nice bowl of warm baking-soda water to gently and effectively clean everything as you go.

Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked