JFI2089WES10 Jenn-Air - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Douglas from Byron, NY
- Parts Used:
- EDR4RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light on to order water filter
Pressed in the end of the filter cover, lowered it down part way. Twisted the old filter 1/4 turn and removed it. Set in the sink to drain. Inserted new filter and twisted it to lock. closed cover. Done. Total time @ 1 Minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jake from Novato, CA
- Parts Used:
- EDR4RXD1
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Removing the existing filter by rotating as directed and then dislodging from 'docking' station proved difficult. Turns out, the old filter is under a bit of vacuum pressure and getting the unit to separate or release was a challenge.
I removed the drop-down outer housing by gently prying the sides of the two pivot pins at the rear. This gave me move 'room' to grip and slightly rotate then pull the old filter forward and away from the tight suction connection. I was concerned that I would be too forceful for the plastic assemblies and would break something; deliberate motions and a steady thought process on the problem helped disengage the darned old filter!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Bethesda, MD
- Parts Used:
- WP12656105, WP12656018
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Broken pins holding pantry door
Removed door and crisper pans.
Removed nuts on left end cap - think there were 3.
Removed nuts on right end cap and one or two on back air regulator attached to right end cap.
Replaced left end cap with new one using reserved nuts.
Carefully removed back air regulator from right end cap.
Attached back air regulator to new right end cap.
Replaced right end cap and back air regulator and attached with nuts.
Carefully inserted pantry door into pin on one side and slightly bent both right and left pins to insert door fully into end caps.
Replaced crisper pans.
That's it.
Removed nuts on left end cap - think there were 3.
Removed nuts on right end cap and one or two on back air regulator attached to right end cap.
Replaced left end cap with new one using reserved nuts.
Carefully removed back air regulator from right end cap.
Attached back air regulator to new right end cap.
Replaced right end cap and back air regulator and attached with nuts.
Carefully inserted pantry door into pin on one side and slightly bent both right and left pins to insert door fully into end caps.
Replaced crisper pans.
That's it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from Lilburn, GA
- Parts Used:
- EDR4RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed to change water filter in refrigerator
The switch-out of the water filter was simple with good instructions on the box.
The part was delivered very, very quickly!
The part was delivered very, very quickly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathryn from Cedar Springs, MI
- Parts Used:
- EDR4RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
water filter needed replacing
I unscrewed the old one and replaced it with the new one. The real benefit was I got the exact part I needed w/o a 30 minute drive and sales people that ignored me. I had gone to the local store the day before and come home with the wrong part because i could not get assistance and the part # I had did not match what was labled on the package. I used the same part # on the website and got exactly what was needed, less that 48 hrs after I ordered it. thanks for the prompt service. we will be a repeat customer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from DINUBA, CA
- Parts Used:
- W10619951
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Water leaking from bottom of refrigerator onto floor
The video on website is very good and explains everything in detail. Just follow the directions. This is EASY!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roland from Alexandria, VA
- Parts Used:
- WP67002659, EDR4RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
The crisper drawers had cracked runners
Crisper drawers:
1. Removed crisper drawers from refrigerator.
2. Removed drawer front decoration panels.
3. Unpacked, inspected and rinsed out new drawers.
4. Attached drawer front decoration panels.
5. Transfered vegetables and fruit from old drawers to new drawers.
6. Installed new drawers in refrigerator.
7. Closed refrigerator door.
8. Total time about 15 minutes, no tools required.
Ice & Water filter
1. Opened filter compartment cover
2. Removed old filter, drained into sink and placed in the trash.
3. Installed new filter
4. Bled the water line with ice water tap button (be aware when the air in the line exits the spigot, it create a lot of spray and you may need to cleanup the water that splash out of the bottom of the container used to capture the water during the bleeding process.)
5. Close the filter cover and refrigerator door.
6. Total time about 10 minutes and no tools required.
1. Removed crisper drawers from refrigerator.
2. Removed drawer front decoration panels.
3. Unpacked, inspected and rinsed out new drawers.
4. Attached drawer front decoration panels.
5. Transfered vegetables and fruit from old drawers to new drawers.
6. Installed new drawers in refrigerator.
7. Closed refrigerator door.
8. Total time about 15 minutes, no tools required.
Ice & Water filter
1. Opened filter compartment cover
2. Removed old filter, drained into sink and placed in the trash.
3. Installed new filter
4. Bled the water line with ice water tap button (be aware when the air in the line exits the spigot, it create a lot of spray and you may need to cleanup the water that splash out of the bottom of the container used to capture the water during the bleeding process.)
5. Close the filter cover and refrigerator door.
6. Total time about 10 minutes and no tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- alvin from irmo, SC
- Parts Used:
- EDR4RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
easy and quick
unscrewed to removed old and screwed in new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Beckley, WV
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
while closing the door, the light switch fouled, resulting in the switch breaking
I used a flat screwdriver and released the lock tab on the bottom of the light switch, and pried the switch out, being careful to not damage the plastic around the mounting place of the switch, unplugged wiring from old switch, plugged in the new one and pushed the new switch into place. Job finished light switch now working.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Traverse City, MI
- Parts Used:
- WPW10655368
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Drip pan in the back bottom was cracked during shipping and leaked
We had periodic leaks from under the Unit from new, could never figure out where it was coming from. Finally as it began to cause damage to surrounding cabinets, we took the back off and found the multiple cracks in the drip pan. Someone had hand trucked it from the wrong side! It was difficult to figure out the fan removal (it sits in the pan) but push the top forward and pull the bottom back and the fan came out. Then the pan was simple to remove / replace, by reversing the removal procedure, the fan was re installed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Dublin, OH
- Parts Used:
- WP12656105
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Broken hinge on bottom drawer lid.
The lid that covers the front of the lower meat / produce drawer hinges upward on two small ( easily broken) plasic pins, one on each side of the drawer. One pin is moulded into each "END CAP" that also supports the drawer glides and glass shelf above. The entire end cap must be replaced to repair the hinge. The left side is easy (it's the only one I had to replace); the right side might be more difficult because the right end cap includes a temperature control.
1) Remove the two produce drawers above the lower drawer.
2) Lift off the front glass shelf support, the glass shelf, and the rear glass shelf support from below the two produce drawers.
3) Slide the lower drawer half way out. Remove the drawer lid by disengaging it from the remaining undamaged hinge pin on the OK end cap. Careful not to break the good one.
4) Slide the lower drawer all the way out, then lift up and towards you to remove it from its glides.
5) Using a 1/4" nutdriver or socket, remove the three recessed screws. Leave the drawer glide alone for now.
6) Pull the front of the end cap up and towards you about 3/4" to disengage it from a small retainig button at the top front. Pull the end cap toward you to disengage the two rear retaining fingers.
7) Using a small Phillips screwdriver, remove the drawer glide from the broken end cap and attach it to the replacement end cap. Note which end is the front before removing it.
8) Reassemble in reverse order. Again, be careful with the hinge pins.
1) Remove the two produce drawers above the lower drawer.
2) Lift off the front glass shelf support, the glass shelf, and the rear glass shelf support from below the two produce drawers.
3) Slide the lower drawer half way out. Remove the drawer lid by disengaging it from the remaining undamaged hinge pin on the OK end cap. Careful not to break the good one.
4) Slide the lower drawer all the way out, then lift up and towards you to remove it from its glides.
5) Using a 1/4" nutdriver or socket, remove the three recessed screws. Leave the drawer glide alone for now.
6) Pull the front of the end cap up and towards you about 3/4" to disengage it from a small retainig button at the top front. Pull the end cap toward you to disengage the two rear retaining fingers.
7) Using a small Phillips screwdriver, remove the drawer glide from the broken end cap and attach it to the replacement end cap. Note which end is the front before removing it.
8) Reassemble in reverse order. Again, be careful with the hinge pins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryan from Panora, IA
- Parts Used:
- WP12656018
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
While cleaning frig, I broke the right side pin the crisper door pivits on.
First I looked at new replacement part, saw what held the part to the frig. Then removed the crisper drawers and vegie drawers and related support pieces. Used socket wrench to take out three screws and started so remove endcap. Realized endcap was attached to a piece that controls air flow to drawer, located supporting screw, removed and entire assembly came right out. I fumbled my way through the linking mechanism being very careful not to force and break anything. Once I figured out how all this worked, it went back together in a few minutes. Replaced the four screws that held the 2 pieces (endcap and airflow) to frig, replace drawer slid, replaced all draws. Done 30 minutes, start to finish. I found Customer Service VERY helpful while ordering piece, couldn't believe it was under $10 and fit exactly! Thanks PartSelect.com!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilynn from Holland, MI
- Parts Used:
- EDR4RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed to replace filter
Turned old one until it snapped out. Replaced it with a turn.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from MARION, IL
- Parts Used:
- 12002355
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The refrigerator was freezing most products
Remove the light cover. Use a flat head screw driver to push in the tabs on the back of the program mount and pull down to expose the computer board. The Thermistor is clipped on under the vent holes on the right side. Cut both wires to remove the old thermistor strip a 1/4 inch off the remaning wires and the new thermistor wires twist both ends together crimp on the wire caps snap in the new thermistor reinstall the program board until the retainer clips snap into place, slide the light cover back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stanley from Gurley, AL
- Parts Used:
- W10827015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wife dropped a gallon of milk on the lid and cracked the see through panel
Pushed the hinge pins aside and removed the old lid.. Reversed the process to install the new lid
Was this instruction helpful to you?
Thank you for voting!