GI15NDXZS2 Whirlpool Ice Maker - Instructions

Took knife and pried out the the damaged switch. Took wires off. Put the wires on the new switch and put it back in the hole. Job finished. The part shipment was very prompt and I am happy. The End!

Pried out old Switch,Hooked wires to new switch Snapped in New Unit.
5 minutes Total Time

Removed old light switch by prying up and out of housing...removed wires (carefully not to get shocked!) and taped to inside of refrigerator housing. Ordered best matching part and rec'd it in a couple of days. Took less than 5 minutes to remove taped wires from side of cabinet and connect to new switch (which was a perfect match to the original equipment) and snap switch back into refrigerator housing! Works perfectly! Thanks!

Popped old one out with knife. exchanged power leads. Popped new switch in. Make sure to unplug refrigerator before you start!

plugged the two wires in and snapped the switch into it's socket.

Super simplet to fix. Popped out broken light switch and unplugged it and replaced with new switch. Received the part one day after ordering it from your company--AWESOME SERVICE AND TURNAROUND TIME!!! Saved at least $100 plus in repair costs/trip charge for something we were able to do. Great experience and would order from your company again. Thank you!

Open appliance door. Removed access plate at lower front (two screws). Removed two screws holding valve in place. Depressed water line retainers and removed water lines from valve. Inserted water lines in replacement valve, remounted valve, reinstalled access plate. Tested operation. (I did install a water filter during the repair to prevent reoccurrence.)

watched the video how to remove, and did it.

Pulled out old switch with needle nose pliers, unplugged old switch and plugged in the new one and snapped back into place. Very easy to repair. Took less than 10 minutes

Purchased the new light switch, used a butter knife to pop the old one out, used the pliers to pull the wires off the metal tabs, replaced the new one with no problem. Took about under 1 minute. Lights are now all working.

It took less that 30 seconds to pop out the old one and less that 30 seconds to install the new one.

Used the butter knife to pry the old switch out, it is a snap in switch so there is a small keeper on the bottom that needs to be pushed in to pop the switch out. Un hooked wires by pulling them off of the terminals (won't shock you) and put them on the new switch and popped it in

Popped out the old one......plugged in the new one and popped it back into place. My wife was happy in have light again in the fridge!

Initially thought I could repair switch, but then discovered spring was broken. Ordered the new switch (Parts Select is very efficient - received switch in 3 days). Was encouraged by the posts regarding the switch installation. I had some difficulty removing the old switch. Used a pocket knife to ease the switch out of the hole to reveal the clip/spring. After noting the clip/spring location I used a small flat-blade screwdriver to release the clip. Even though I released the "molded" clip/spring(be sure to note where the spring is on the new switch and release it on the switch it was tight in the hole and had to use pliers to carefully remove the old switch. After removing the old switch, used pliers to gently remove the wire leads. Then install the leads on the new switch. Note the orientation for replacing the switch and gently feed the connecting wires into the hole so they won't kink or prevent the switch from entering the hole. Install the switch noting the clip/spring location and the orientation of the lever that the door closes on to turn off the light. Be sure to put it in without binding at an angle. Thanks to Parts Select for this service! I'll definitely be back.

Installing the switch was a breeze, the tough part was removing the old switch. I watched a video on the PartSelect website which showed how to remove and reinstall the switch. I attempted to remove the switch the same way that they showed on the video, but the problem was my switch was surrounded with foam insulation which was stuck to the old switch. I attempted to pull out the switch but was not able to extricate the switch. Finally, I called a friend who works with these switches and he cut away the foam insulation and removed the switch. Being the handyman that I am, I was able to reinstall the new switch. Hope this helps anyone with an Amana refrigerator that has the light switch on the side wall instead of in the light console like the video showed. Don't be afraid to cut away the foam on the right and left sides and the bottom. Don't cut away at the top, because that is where the wire connections are located and you might cut those off and then you'll be ordering more parts. Good luck.