GI15NFLTS0 Whirlpool Ice Maker - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- guadalupe from RIALTO, CA
- Parts Used:
- W10124096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Motor sounded like a small little airplane under my fridge, very loud.
Unplugged the fridge first then took the bottom panel off with a 1/4 inch nut driver. Disconnected the wiring & used my ratchet to reach the 3 screws that held the motor. Took me longer to clean the bottom of the fridge then the installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from BLACKLICK, OH
- Parts Used:
- W10124096
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
loud griding noise
stopped the fan and noise stopped ordered fan motor and fan with interface cable. Using 1/4 inch nut driver to remove screws from motor bracket installed new motor and runs like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from BULLHEAD CITY, AZ
- Parts Used:
- W10124096
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Noisy condenser fan
I suggest following video supplied with order confirmation perfect fit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from RICHMOND, VA
- Parts Used:
- WPW10217917
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Valve needed replacement - ice had become very thin
Just install the new valve by reversing the process of removing the old valve. Only possible nance is with the quick release hose fittings - the collar is pushed down to release the hose. Also, be sure to FULLY reinsert the hose in the new valve. Best to twist the hose a bit when inserting so it goes through the o-ring inside the valve. If not fully inserted, it will leak.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Huntsville, AL
- Parts Used:
- W11566407, WPW10548509, W11566405
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
One of the circulation pumps was going bad and making a loud noise.
I replaced the two pumps, since both were the same design...figuring if one went bad then the other would soon go bad...and then I also replace the water level sensor. All had quick connect plugs. The time is just taking apart the various pieces, cleaning, installing the new pumps and sensor, then reassembling.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Atlee from Jupiter, FL
- Parts Used:
- WP2149705
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
broken light switch
Figured out You have to pop off the cocer than remove the 1/4 hex head screws only not the philips ones
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frances from palm beach gardens, FL
- Parts Used:
- WP179051
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
range handle fell off and screw got lost
It was worth the money for that little screw, since I didn't have to run all over trying to find the right one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barton from Ringgold, GA
- Parts Used:
- WPW10217917
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
leaking water inlet valve
Received replacement valve ~ 3 days, easily replaced in less than 15min, works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lindey from Austin, TX
- Parts Used:
- WPW10217917
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Freeze ruptured inlet valve
Simple to replace. Next fall I will be sure to drain the outdoor icemake and shut it down for the winter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- otis from frenchburg, KY
- Parts Used:
- WPW10217917
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
water leaking from water control board.
After turning off water to icemaker, defective control removed (two screws) and new unit installed.Worked perfectly.I was totally amazed when I ordered the part thursday afternoon and it arrived fridaY morning.Total time out of operation less than 24 hours.Wonderful results.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from glen gardner, NJ
- Parts Used:
- W10124096
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set, Wrench set
Unit very noisy when running sometimes and then get quiet the noise would vary
Remove back panel on unit locate condenser fan and motor remove three small screws holding motor assembly to metal bracket disconnect electrical connection press new fan blade on new motor reverse directions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Frisco, TX
- Parts Used:
- W11566405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Water was not circulating to the freeze area
Easy. I took a picture with everything in tact. Took apart a couple of parts with screw driver. Replaced the pump. Put it all together and it worked fine.Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sean from Simi valley, AL
- Parts Used:
- W10124096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
condenser fan would not come on, and when it did, made loud noise.
Repair was so simple, I didn't even need instructions. Removed old fan with motor, installed new one, installed harness that converted plugs, done. Saved hundreds of dollars doing the repair myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- eBooks4u from Wimberley, TX
- Parts Used:
- W10124096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Noisy fan motor
Before I began I unplugged the electrical at the wall outlet. 1. Unscrewed the 4 mounting screws. 2. disconnected electrical at the motor. 3. removed the assembly. 4. mounted the new motor on the assembly as described in the instructions. Installed the assembly and reconnected the electrical. Works great, easy job!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Fort Mohave, AZ
- Parts Used:
- W10124096
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
loud noise coming from back of fridg.
Unplug A C Cord . Simply unscrewed lower back cardboard cover panel and unscrewed condenser fan motor , removed wiring plug , pulled fan motor out removed fan blade and put it on new motor . then I Reinstalled motor. Noise is gone . EASY INSTALLATION .
Was this instruction helpful to you?
Thank you for voting!