3ECKMF87 Whirlpool Ice Maker - Instructions

It took both me and my wife! One of the new parts we recieved was broke so we took the part off of the one that didn't work.

Unplug the fridge. Used the screw driver to remove the motor. Easy. Now putting the new one in was difficult because it has to line up exactly.
Thats what took 15 minutes but after me and my wife worked on it, we had a bucket of ice by morning!
We only knew how to do what we did because of reading these messages on this site. It came with no directions.

unpluged the refrigerator, remove three screws holding ice maker in place, disconnected wire clip, removed front of icemaker by relaesing two clips holding it in place. the module and motor assembly are held in place with three screws. put the icemaker together and replaced it in freezer, and pluged the cord back in. the icemaker started making ice in about 15 minutes. very easy fix

Removed the two screws holding the funnel in place...removed the old one and replaced it witht he new tubing...screwed screws back in and the jov was complete. It actually took longer to get it out of the sack than it did to put it together

removed icemaker timer/controler replaced with new part.reinstaled it works perfectly

I determined that the plastic lever inside the icemaker was broken and I found the part easaly. It was farelly inexpensive considering the important job the ice maker does, so I order it and paid for the standard, 5-8 days delivery. To my surprise, it was delivered (to my neighbors house thanks to the delivery person) the next day. Once Berry the neighbor delivered it to my house, 15 minutes later ice was being made. I had to remove one screw and losen two on top of the icemaker, disconnect power and remove the icemaker. I don't think that this step was even required but I wanted to remove all of the old ice from the maker without thawing out the freezer. Replacing the part itself also required removal of three screws. I think that almost anyone can do this easily (with or without Berry).

I unpacked the motor and looked at how it was supposed to go in. I removed on screw in the right rear of the ice maker. Pushed a tab on the left of the ice maker. Removed the entire assembly and unhooked the electrical part of the ice make. unscrewed the three screws holding the motor in place and replaced the motor. Put everything in back together and in 15 minutes the familar sound of the ice maker could be heard.

I ordered the part and just 1 1/2 days later, it arrived! Awesome!

I took the cover off the ice maker motor. Then I simply unscrewed the three screws holding the motor in place (be VERY careful - the hinge mechanism that holds the ice maker on/off bar needs to be gently removed from the motor so the prongs do not break).

Once the motor and ice maker hinge were removed, I simply pushed the new motor on, screwed all three screws back in, put the cover back over the motor, pushed the bar to 'on' and water flowed and ice was made! I turned it to Max so I would have lots of ice in a short amount of time then returned the switch to Normal and I've not had a problem since.

I unscrewed the fill tube screws from the back of the fridge, and pulled the tube out.

Then I put the new tube in, screwed the screws back in and reconnected the waterline.

sears wanted $450 to replace ice maker or $400 for refubished. I ordered a $60 motor/control unit from parts select. Remove ice maker, remove motor cover, three screws replace and ice within the hour.

Simply removed the old and replaced with the new part.

remove the wiring cover, pulled out the ice maker shelf, unpluged the wiring. Once out I removed the control module cover and remove 3 screws and pulled out the old control module. I pushed on the new control module and reattached the 3 screws, attached the module cover and plugged wiring in, slide back into the freezer track, installed wiring cover and screw- 15 minuits tops

Followed video lnstructions which were very good. Have used your web site in the past and will continue to purchase products. Thanks.

First I replaced the thermostat. (from this company.) Same thing happened. Then I thought the ice heater has too low voltage and does not melt it for extraction. So, I put a short on the relay on the beam receiver board. No difference. Then completely disassembled the ice maker, and discovered the shaft cracked on the plastic gear, which rotates the ice extractor. So, I ordered and received this control assembly. Put together the unit and having ice again. Due to the cracked gear the thing was out of timing. This gear drives the contactor for letting water in, freezing time, heating the ice, (so it slides out easily), etc

I followed the simple steps outlines in the great video! Thanks

I removed the two screws that hold the ice maker door. I then removed the single screw on the right underside of the ice maker. I depressed the plastic "catch" on the left underside of the assembly and the whole thing just pulled straight out. I then disconnected the wire harness.

The module cover is removed, then the module itself is easily removed by removing three screws.
The assembly is just as easy.

A few hours later, I had a half bucket of ice!