GI15NFLTB0 Whirlpool Ice Maker - Instructions

Just install the new valve by reversing the process of removing the old valve. Only possible nance is with the quick release hose fittings - the collar is pushed down to release the hose. Also, be sure to FULLY reinsert the hose in the new valve. Best to twist the hose a bit when inserting so it goes through the o-ring inside the valve. If not fully inserted, it will leak.

Unplugged the unit. Removed 2 screws to remove front cover to access the cutter grid.removed 2 screws to the cutter grid, unsnapped power connector and removed broken grid. Slid new grid in place, reconnected power connector, replaced screws, plugged in ice maker and slid back in place. Very easy!!!

Removed broke wire and replaced new wire. Use gloves to pull the wire tight. That's very important.

(1) Ordered PS371704 from PartSelect! Best advice EVER! (2) Unplugged refrigerator (since the water solenoid on the back of the refrigerator is powered to switch ON the water, you NEVER have to turn off the water!) (3) Pull off the refrigerator's bottom grill. (4) With a small saucer under the fittings, unscrew the black and white tube fitting. There is only one nut to remove on the white tubing side. You'll need to undo the compression fitting on the black tubing and slide off the compression nut. You'll need to MAKE SURE you keep these nuts and replace onto the black and white tubing the SAME WAY you took them off. You'll NOT need to use nut drivers as finger tight is the key. Too hard and you'll ruin these plastic nuts. You should get only about 1/8 cup or less of water during this whole exercise. (5) Cut off the old, broken water nozzle. (4) Find a screw of the appropriate size to fit tightly 1/2 way inside the new tubing (this is to ensure your old and new tubing are connected to feed through the door). If screw is not tight within the tubing, wrap part of a plastic (thin) sack around this screw a couple of times and force into the tubing. You'll, of course, then need to use the hacksaw to cut the head off the screw as you'll be forcing the other half of the screw into the old cut tubing (6) Chase the dog out of the kitchen and cajole your wife (significant other) to push the newly joined tubes through the top of the dispenser, through the door and out the bottom as you will be gently PULLING on this old tubing from the bottom until the new tubing pops through the doors bottom. (7) Once this new tubing is out, you will separate the old tubing and, using the nuts in the proper sequence, connect this new tubing to the white tubing. (8) Plug the refrigerator back in and test flow the water. Check to ensure the plastic nuts have no leakage ... button up the bottom grill ... and enjoy the fresh water! PS> Don't forget to praise the wife (significant other) and give the dog a treat for staying out of your face!!

I replaced the two pumps, since both were the same design...figuring if one went bad then the other would soon go bad...and then I also replace the water level sensor. All had quick connect plugs. The time is just taking apart the various pieces, cleaning, installing the new pumps and sensor, then reassembling.

Figured out You have to pop off the cocer than remove the 1/4 hex head screws only not the philips ones

It was worth the money for that little screw, since I didn't have to run all over trying to find the right one.

Received replacement valve ~ 3 days, easily replaced in less than 15min, works great

Simple to replace. Next fall I will be sure to drain the outdoor icemake and shut it down for the winter.

After turning off water to icemaker, defective control removed (two screws) and new unit installed.Worked perfectly.I was totally amazed when I ordered the part thursday afternoon and it arrived fridaY morning.Total time out of operation less than 24 hours.Wonderful results.

Unplug regrigerator power cordfrom wall outlet. Using nut driver remove cover from lower back side of refrigerator. Unplug wire connection to fan. Using nut driver remove the four screws holding the fan/bracket assembly. Carefully remove fan/bracket assembly from refrigerator. Using nut driver,remove the old fan from fan bracket. Using nut driver install new fan on fan bracket. Carfefully install new fan/bracket assembly and install the four screws. Plug wire connection to fan (you may need to use adapter supplied with new fan). Reinstall refrigerator lower back cover. Plug refrigerator power cord back into outlet. Note: you may wish to carefully vacuum dust from back of refrigerator before installing back cover. You should also vacuum dust from front side.

Disconnected power cord, removed rear cover of refrigerator, disconnected pig tail, removed 4 housing screws, took three mount screws out and removed old fan. Reversed steps, plugged in and complete repair done.

Unplug A C Cord . Simply unscrewed lower back cardboard cover panel and unscrewed condenser fan motor , removed wiring plug , pulled fan motor out removed fan blade and put it on new motor . then I Reinstalled motor. Noise is gone . EASY INSTALLATION .

Watched the video that was attached to my order confirmation (great idea) and just followed it step by step. Real easy repair since I had tried to fix the noise first without ordering parts, so I knew what I was doing Did a temporary fix which quieted it down while I waited for the parts and then the repair itself was pretty straight forward.

Remove back panel on unit locate condenser fan and motor remove three small screws holding motor assembly to metal bracket disconnect electrical connection press new fan blade on new motor reverse directions