MIM1555YRS2 Maytag Ice Maker - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gerardo from Berwyn, IL
- Parts Used:
- W10124096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Loud noise coming from rear of fridge.
It was very easy. The part make look different online but it was a proper replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Birchwood, TN
- Parts Used:
- W10124096
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
a rumbling noise was comming from the back of the fridge
I unplugged the appliance removed the back cover exposing the fan motor.Unplugged the wiring harness from the motor assembly.unbolted the fan motor mounting bracket,and removed. Next I unbolted the fan and motor assembly from the mounting bracket.( I pulled the whole bracket out so it would be easier to reinstall the motor and fan assembly,then reinstalled the bracket with the motor and fan already installed) I installed the bracket assembly with the motor and fan back to its location,plugged the wiring harnessback to the motor. replaced the bask pannel ,and plugged the 110 back in the wall socket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rex from Amarillo, TX
- Parts Used:
- W10124096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
replaced motor and fan
I have a grandson that works for Pantex. He replaced the fan and motor in less than ten minutes using only the nutdriver tool. My cost compared to local supplier and labor was about 75% less.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Spring Hill, TN
- Parts Used:
- W10124096
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Condenser motor was making noise.
Removed the cardboard baking on back. Unplugged the fan. Used 1/4 socket and removed the 3 nuts. Removed the fan. It is tight quarters. Take your time and the job will go fast.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from HEBER SPRINGS, AR
- Parts Used:
- WPW10548509
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
only a partial refill of water bucket (would then run dry and make pump noise)
my sensor was stuck because of age, so I had to remove the water bucket to pry it out. It is easy to see what you have to remove to get to it. I used the mirror and rachet, extensions, 1/4 socket to remove screws. Tips - Remove the plastic door-inner to help working inside the bin. Also plug the drain because you will drop screws. Magnet sockets don't work on stainless steel. Later I found it is much easier to work inside the bin by pulling the entire unit out (shut off water and power, remove lower panel and disconnect drain tube). It sounds hard, but actually is easy. REMOVE THE TOP (4 screws). it stays connected because of wiring, but it allows full access and makes all kinds of repairs easy, especially pump replacement and even the circuit board behind the front panel buttons if you ever get to that point.
BTW Partselect is awesome, I have used a number of times for ice maker and dishwasher. My next project is the washing machine! Always the right part shipped very quickly.
BTW Partselect is awesome, I have used a number of times for ice maker and dishwasher. My next project is the washing machine! Always the right part shipped very quickly.
Was this instruction helpful to you?
Thank you for voting!
pump making noise
The pump was making noise, so I decided to replace both pumps. I had to remove the water bucket to get to the pumps which are easy to change out once there. It is easy to see what you have to remove to get to it. I used the mirror and rachet, extensions, 1/4 socket to remove screws. Tips - Remove the plastic door-inner to help working inside the bin. Also plug the drain because you will drop screws. Magnet sockets don't work on stainless steel. Later I found it is much easier to work inside the bin by pulling the entire unit out (shut off water and power, remove lower panel and disconnect drain tube). It sounds hard, but actually is easy. REMOVE THE TOP (4 screws). it stays connected because of wiring, but it allows full access and makes all kinds of repairs easy, especially pump replacement and even the circuit board behind the front panel buttons if you ever get to that point.
The pumps weren't the problem. The water bucket was only parially filling causing the pump to make noise. The problem was the WATER INLET VALVE. It is super easy to replace. Just remove the lower panel, and the valve is right there. Shut off power and water. To disconnect the hoses you PULL on the little fittings attached to the valve and then pull out the hoses. Took me 15 minutes.
BTW Partselect is awesome, I have used a number of times for ice maker and dishwasher. My next project is the washing machine! Always the right part shipped very quickly.
The pumps weren't the problem. The water bucket was only parially filling causing the pump to make noise. The problem was the WATER INLET VALVE. It is super easy to replace. Just remove the lower panel, and the valve is right there. Shut off power and water. To disconnect the hoses you PULL on the little fittings attached to the valve and then pull out the hoses. Took me 15 minutes.
BTW Partselect is awesome, I have used a number of times for ice maker and dishwasher. My next project is the washing machine! Always the right part shipped very quickly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from IMPERIAL, MO
- Parts Used:
- WPW10503764
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
went good
went good
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- M Edward from Timonium, MD
- Parts Used:
- WPW10503764
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker Thermostat not shutting off the making of ice
un screwed the hex screw holding the thermostat and installed the new thermostat and pluged the new part int its place. I undid the front shield so i could get to the plug.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimena from FARMINGTON, CT
- Parts Used:
- W11566405
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Old pump gave up
Followed instructions in Sears parts website. Not difficult but tricky to get screws out and back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Powell, OH
- Parts Used:
- WP2313637
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver
Cutter on Ice Maker failed and needed to be replaced
I completely broke down the unit cleaning or replacing any part with rust. The replacement grid assembly (cutter) came from partselect within days of ordering. I was able reassemble the unit with the new grid assemble. Now have fresh ice. Thanks Partselect... you made this do-it-your-selfer very HAPPY! My wife cannot beleive I got the unit back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from BLACKLICK, OH
- Parts Used:
- W10124096
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
loud griding noise
stopped the fan and noise stopped ordered fan motor and fan with interface cable. Using 1/4 inch nut driver to remove screws from motor bracket installed new motor and runs like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from PHOENIX, AZ
- Parts Used:
- WP2313637
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Replace the ice cutter grid.
The real difficulty is removing the screws. Even with a nut driver the space available makes them difficult to remove. I went to the hardware store and replaced the screws with screwdriver slots for re-installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from BULLHEAD CITY, AZ
- Parts Used:
- W10124096
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Noisy condenser fan
I suggest following video supplied with order confirmation perfect fit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Guy from SURFSIDE BCH, SC
- Parts Used:
- W11566405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Disherwasher would not start
Found fault with recirculating pump. Found hot spot on pump circuit board . Replaced pump
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DANIEL B. from ROCHESTER, IN
- Parts Used:
- W10124096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Refrigerator was very noisy. Investigation revealed that the condensor fan motor was going bad.
First let me say that the instructional video on your website for this repair was very informative. My son and I watched that before we began the repair. We unplugged the unit first. After removing the back cover, he unplugged the old fan's electrical connection, and then proceeded to remove the fan and bracket from the unit. We then removed the old fan from the bracket, installed the new one and then he reinstalled the new fan and bracket back into the unit. He used the included electric adaptor cable to complete the electrical connection, plugged in the refrigerator briefly to confirm all was well (it was), then replaced the back cover and we were done.
Was this instruction helpful to you?
Thank you for voting!