UNVIM98 Maytag Ice Maker - Instructions

Removed Ice tray and flap followed by the three screws that held the old ice maker in place. (I probably didn't have to remove the top two, they are designed to just loosen and lift up on the mecanism to free.) I then pulled the old wiring harness out of the original ice maker. A small screw driver helped in depressing a tab while pulling on the harness. The same process was used to remove the wiring harness that was attached to the new replacement unit. I connected the original wiring harness that I had disconnected from the bad ice maker, and it fit perfectly into the replacement unit. No need to splice or use any of the harnesses that came with replacement. I tried installing the new unit and discovered that there was interfernce with the water feed hose. I had forgotten to break off the tab on the end of the replacement unit. Once I did that using pliers, the unit fit fine. I tightened the screws, installed the on/off mecanism and replaced the tray and flap. I then waited and waited, hoping to hear the forgotten sound of water entering the ice maker. Had a beer and walked the dogs thinking I had failed, but low and behold, over an hour later, the ice maker turned on the water. Many hours later, my wife woke me up in the middle of the night to declare we had cubes! Success.

I removed the 2 screws on top and the one screw underneath holding the Ice Maker to the wall of freezer.I pulled the electrical connection from the wall next (wiggled it back and forth until it came out).
I matched it up to the picture from this site and ordered the replacement unit.
When it arrived, it had a lot of extra parts to match up to mine and any other fridge.
A good tip is to keep the old unit so you can configure the new unit the same. Although it was easy, this took me the longest of the entire job. Once this was done, it took me !0 minutes to plug the new unit into my fridge and then attach it back to the wall with the 3 screws.Not a hard job.Thanks

I just removed three screws from the old ice maker and disconnected a single set of wires. All I had to do was reconnect the new set of wires and screw it back into the side of the freezer. Anybody could do this repair.

The ice maker is held in by three screws. There is an electrical connection. Also, there is a water line to the rear of the unit.
The replacement unit had clear instructions and a selection of parts to match the defective device.
Hint: don't discard the old unit until the new unit is configured for installation.
Turned on the water and the electricity to the fridge, and had ice in several hours.

i can't believe it was that easy, just removed the screws, pulled elements out disconnected wires well it seemed to easy so had to read the directions or it would have took only 10 minutes. to do this job. thanks so much for your web sight, the repair man said it would probably be 200.00 or so

yea right 100.00 and its making all the ice we need thanks

joan mcquain

it was very very simple, it took only three screws
using socket set.
I removed the old one and put the new one in place , connect electric connection in 2 seconds snapping it toghether, that is all to it.
the hardest part is waiting on the ice to be made , which it took three to four hours for the first batch.
I am in the medical profession, IF I CAN do it , everyone CAN!!!!!!!!

Replacing the ice maker is no big deal. Just take out the old one and replace it with the new one. The replacement, however, didn't work very well. Seemed like its timer was off, so it would dump ice cubes before they were completely frozen. So, we go shells of ice cubes. Not good. Called Parts Select, advised them of the problem, and they agreed to replace the part. Could not be happier with the customer service I received from this company.

It was very fast and easy. Two screws to take of the ice door cover. the ice maker itself just slid out and all I did was disconnnect the wiring harness. Unscrewed the plastic bottom case and screwed onto the new one. Attached the harness and slid it back in.

3 screws and plugged in the new ice maker. It was slightly difficult to unplug the old ice maker and place the plug in the new ice maker. Still really easy. New ice maker works great!

First I unpluged the refriderator and removed the old ice maker. I then just simply installed the new ice maker. It was just that simple. The next morning I woke up with a full tray of ice.

This was an easy repair.

First I turned off the breaker that supplies power to the refrigerator, then I followed instructions to remove the old ice maker. I removed the bottom screw and loosened the two top screws and it came out easily.

The only unexpected problem I ran into was that the connection at the refrigerator end was 'hard wired', i.e., the wiring harness was not removable from the freezer.

After disconnecting the wiring harness from the old ice maker, all I had to do was plug the wiring harness into the new unit, slide it into place, then replace the bottom screw and tighten the two top screws.

Turned the power back on and had ice within 1/2 hour! : )

First removed 3 screws and took out old ice maker, punched out water inlet tube area in new ice maker connected the electric and screwed it back in. Within an hour...heard the ice drop. (I did not do the repair, my boyfriend did, however I think I could have done it.

unscrewed 4-5 screws; unplugged; attached arm; installed; reverse pattern. truly easy. cost 1/3 what repair man quoted me. this is easy!

Removed two screws, pulled the element out and disconnected the wire harness. Reversed the procedure and we were one.
Kept a close watch n the ice maker to make sure we didn't have another flood. The first time an ice cube stuck between the metal bale and the side of the freezer--we had about 50 gallon of water on the floor. Thought we had it fixed and a few days later another flood. Decided to replace the unit and it is working great...Hopefully no more floods.

Looking at the instructions it looked like I had to rewire the the plug in the adapter. As it turns out, you don't .Using a screw driver, I released the braket mount and the nut driver loosened the nut holding the tray to the wall. It came right off when you lift it straight up and the wire assembly was exactly the same as the original. All I did was plug in the new ice maker, Hang the assembly on the loosen nuts and tighten again and put the screw back in the bottom bracket that held it in place. I spent longer looking at the instructions than I actually did in the whole replacement time. By morning we had a good amount of ice. EASY>>