12001747 Maytag Ice Maker - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dean from Kankakee, IL
- Parts Used:
- 61005614
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
auger motor for ice maker blew out back of enclosure
remove ice bin,remove 1 screw on bottom of left side of enclosure, unhook harness and remove entire enclosure incuding auger moter. remove screws that hold auger motor to enclosure. remove screws holding solenoid to enclosure. re-install in reverse order, very simple repair. ordered part on monday afternoon it was on my doorstep on tuesday morning. very speedy delivery was really impressed , thank you very much!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Antelope, CA
- Parts Used:
- WP61003336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice maker would stop dispensing ice,shaft would stall.
Checked the ice tray and could only find the drive ring had some breaks in the plastic. Actually did not see why this would stop the auger from turning and dispensing ice. However this was the only thing I could find wrong with the unit. I pulled the tray, removed 6 screws (star tip heads) pulled the auger forward and replaced the drive wheel, put the unit back together and its been working fine ever since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jesus from Santa Maria, CA
- Parts Used:
- WP61003336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
ice bin drive ring was cracked
removed torx screws and replaced ice bin drive ring.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Avon Park, FL
- Parts Used:
- 61005614
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Motor mount broke out of ice enclosure when auger locked up.
Removed broken enclosure,mounted the motor and solinoid on the new unit.Then installed it back into the ice maker. WE HAVE ICE AGAIN!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Maryland Heights, MO
- Parts Used:
- 61005614
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
case plastic broke where motor attaches
The only hard part of this rapair is getting the auger off the motor. I wasted a lot of time before driving to auto supply store and buying a set of thin needle nose locking plyers so I could get a true grip right behind the auger. Once I had that, it was just a matter of a lot of brute force and a second pair of big locking pliers I already had for grip on the auger.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ross from Chandler, AZ
- Parts Used:
- WP61003336
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Loud crunching and banging from ice dispenser
Problem caused by ice cubes falling out of ice bin and collecting at rear and interfering with ice dispenser drive. Broke plactic drive ring. Pull down 2 clips at front bottom of ice bin. Pull ice bin out. Dump ice cubes. Remove 8 star drive screws to allow case to move far enough to clear broken drive ring. Replace drive ring. Reinstall and tighten 8 screws. Install ice bin. Correct loose right side ice cube retainer board to prevent cubes from falling out of ice bin.
Was this instruction helpful to you?
Thank you for voting!